- (1) Pair of Rockville RV65.2C 6.5" Component Car Speakers 750 Watts/140w RMS CEA Rated
- (1) Pair of Rockville RV6.3A 6.5" 3-Way Car Speakers 750 Watts/140 Watts RMS CEA Rated
- (1) Rockville dB55 4000 Watt/980 Watt Dyno-Certified RMS 5 Channel Amplifier Car Stereo Amp, Loud!
- (1) Rockville RWK4CU 4 AWG Gauge 100% Copper Complete Amp Installation Wire Kit OFC
- (2) Rockville RTR172 17 Foot 2 Channel Twisted Pair RCA Cable Split Pin 100% Copper
Video of RV65.2C:
Includes:
- (2) 6.5” speakers
- (2) tweeters
- (2) Crossovers
- (2) Grills
- Flush and surface Mounting accessories
- Speaker wire
Rockville car audio speakers utilize the latest in speaker technology for superior sound quality. We use top quality polypropylene cones which are known for their high damping qualities. This means they can have a controlled break-up, which results in a smoother high frequency roll-off. Our Flexmotion Butyl Rubber Surrounds give the speakers a smooth response with minimal distortion. For smooth and extended high frequency sounds we used high temperature PEI dome tweeters with ferrite magnets. The RV series speakers are designed with superior SPL response and extremely high power handling making these perfect for use with the amp built into your receiver or with a high powered external amplifier. Due to their shallow mount design, these speakers fit in 97% of all vehicles.
CEA Rated.
Rockville car audio speakers are CEA rated, what that means is that the
Consumer Electronics Association recognizes these speakers to be
accurately rated and meet their rigorous standards for wattage, SPL and
frequency response. So while other manufacturers state
“out-of-this-world” wattages on their products, you can rest assured
that your Rockville speaker will work up to spec. and exceed your
expectations.
Top of the line components!
Rockville speakers only use the best sourced components. We use
efficient and high powered magnets along with aluminum voice coils wound
with 100 % oxygen free copper. We pay attention to every detail
ensuring you get the best sound in your car.
Features:
- Rockville RV65.2C 6.5"/6" Component car speakers (pair)
- Peak Power Rating: 750 Watts per Pair / 375 Watts Each
- CEA Compliant RMS Rating: 140 Watts per Pair / 70 Watts Each
- Injection Molded Polypropylene woofer cone gives amazing bass and mids
- Flex Motion Butyl Rubber Surround
- 1.2” PEI dome tweeter with ferrite magnet give amazing highs
- Flush and surface mounting tweeter options
- Fine-tuned 2-Way Crossover, 12db/Octave Roll Off
- Ferro Fluid Cooled Tweeter Magnet
- Steel high quality basket
- Rubber magnet boot cover
- Frequency response: 34-22,000 Hz
- Crossover will cut anything lower than 3.5 Khz @ 12 dB / octave slope from the tweeters
- Crossover will cut anything higher than 3.5 Khz @ 12 dB / octave slope from the woofers
- Sensitivity: 91 dB @ 1w/1m
- Mount depth: 2.17"
- Impedance: 4 Ohm
- Grilles included
- Aluminum voice coils
- 100% oxygen free copper voice coil windings
- Black electro-plated T-yoke and washers
- Cotton spider material
- Copper terminals
- Cutout diameter: 4.92”
- Magnet: 8 Oz Y25 magnet
- Magnet dimensions: 80mm x 12mm
- Fs: 95.37 hz
- Re: 3.6 OHM
- Qes: 1.494
- Qts: 0.864
- Qms: 2.049
- Fits 6” and 6.5” openings
- Top mounting depth of woofer: 2.17” Inch (95% of installs use the top mounting depth)
- Bottom mounting depth of woofer: 2.6” inch (This measures the speaker from top to bottom)
- Top mounting depth of tweeter: 0.79”
- Bottom mounting depth of tweeter: 1.18”
- Tweeter mounting diameter: 1.93”
Video of RV6.3A:
Description:
Rockville car audio speakers utilize the latest in speaker technology for superior sound quality. We use top quality polypropylene cones which are known for their high damping qualities. This means they can have a controlled break-up, which results in a smoother high frequency roll-off. Our Flexmotion Butyl Rubber Surrounds give the speakers a smooth response with minimal distortion. For smooth and extended high frequency sounds we used high temperature PEI dome tweeters with ferrite magnets. The RV-A series speakers are designed with superior SPL response and extremely high power handling making these perfect for use with the amp built into your receiver or with a high powered external amplifier. Due to their shallow mount design, these speakers fit in 97% of all vehicles.
CEA Rated.
Rockville car audio speakers are CEA rated, what that means is that the Consumer Electronics Association recognizes these speakers to be accurately rated and meet their rigorous standards for wattage, SPL and frequency response. So while other manufacturers state “out-of-this-world” wattages on their products, you can rest assured that your Rockville speaker will work up to spec. and exceed your expectations.
What’ so special about Rockville Speakers “in engineering terms”.
The acoustic center of a driver is the point in the driver from which the sound appears to originate. What is crucial in a good multi-element design is the difference between the centers of the drivers. This is called relative acoustic offset. A good speaker design features phase accuracy in and around the crossover point, because the interaction of the drivers is most affected by the SPL magnitude and phase in this area. The Rockville designs allow for wide dispersion of the sound for complete musical immersion.
Audio power is the electrical power transferred from an audio amplifier to a loudspeaker, measured in watts. The electrical power delivered to the loudspeaker and its sensitivity determines the sound power level generated with the balance being converted to heat. Amplifiers are limited in the electrical energy they can amplify; loudspeakers are limited in the electrical energy they can convert to sound energy without distorting the audio signal or destroying them selves. These power ratings are important to consumers finding compatible products and comparing competitors. Because Rockville products are CEA rated, you can easily and accurately match any Rockville speaker to a CEA rated amplifier and be guaranteed of their performance match.
Features:
- Pair Rockville RV6.3A 6.5"/6" 3-way car speakers
- Peak Power Rating: 750 Watts per Pair / 375 Watts Each
- CEA Compliant RMS Rating: 140 Watts per Pair / 70 Watts Each
- Polypropylene woofer gives amazing bass and mids
- Flex Motion Butyl Rubber Surround
- 1.2” PEI dome tweeter with ferrite magnet give amazing highs
- 0.6” super tweeter
- Steel high quality basket
- Rubber magnet boot cover
- Frequency response: 34-20,000 Hz
- Sensitivity: 91 dB @ 1w/1m
- Mount depth: 2.12"
- Impedance: 4 Ohm
- Grilles included
- Aluminum voice coils
- 100% oxygen free copper voice coil windings
- Cotton spider material
- Copper terminals
- Cutout diameter: 4.92”
- Magnet: 8 Oz Y25 magnet
- Magnet dimensions: 80mm x 12mm
- Fs: 85.94 hz
- Re: 3.6 OHM
- Qes: 0.032
- Qts: 0.021
- Qms: 0.063
- Fits 6” and 6.5” openings
- Top mounting depth: 2.13” Inch (95% of installs use the top mounting depth)
- Bottom mounting depth: 2.44” inch (This measures the speaker from top to bottom)
Video of dB55:
Description:
The dB55 is a 5 channel amplifier with 4,000 watts peak output and 980 watts Dyno Certified power. Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market. The peak rating can be used to compare with brands who use peak ratings such as Boss and Power Acoustik while the Dyno Certified RMS can be used to compare with top brands such as Kicker, Rockford, Alpine, etc.
This amp has a fully adjustable 12dB/Octave crossover with differential circuitry. Other features include a subsonic filter, a fully adjustable bass equalizer, and mute and delay soft start technology. The dB55 is protected by a full IC controlled circuit and has professional peak limiter circuitry guaranteeing distortion free music playback at all levels.
The dB amps by Rockville use the top parts and components recommended by Rockville’s very own engineer. These amps are the best sounding out of any series we have ever created. They perform more efficiently resulting in even dB of sound. We created them to be 2 ohm stable just like the world’s most famous amps by Rockford Fosgate, Kicker, etc. If you compare our amp to the most famous amps you will find our amp can compete and, in my opinion, surpass the performance of anything in its class.
Each and every amplifier we manufacture is tested twice. Once at the semi-finished PCB stage of production, and then another test is done at the final assembly. We also run age tests on them. After this is all done, we hire a 3rd party independent company unaffiliated with our factory or with us to go to the factory and inspect 20% of all the production items. We test the power, the controls, and over 20 other tests. We guarantee these amps will satisfy you. We are so confident in your satisfaction of this amplifier that we will offer you a 90 day money back guarantee. If this amp does not perform as well as you expected we will send you a pre-paid shipping label and give you all of your money back. This means if for any reason you want to return the amplifier back for a full refund within 90 days, you can! (Amp must be complete along with the box).
Includes:
- Amplifier
- Bass Remote
- Birth sheet with tested power
- Owner’s manual
- Mounting Screws
- Warranty
Features:
- Rockville dB55 4000 Watt/980 Watt Dyno-Certified RMS 5 Channel Amplifier Car Stereo Amp, Loud!
- Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
- 2 Ohm: 120 Watts x 4 + 500 Watts x 1 <1% THD+N
- 4 Ohm: 80 Watts x 4 + 300 Watts x 1 <1% THD+N - Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
- 2 Ohm 480 Watts x 4 + 2000 Watts x 1
- 4 Ohm: 320 Watts x 4 + 1200 Watts x 1 - High-Speed MOSFET Power Supply
- Rugged switching MOSFETs for Class D in CH5
- Under Voltage Protection at 10V
- Over Voltage Protection at 16V
- Optical Coupler Class “AB” +“D” Technology
- Studio-Grade Bipolar Output Stage Transistors
- Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
- Low Pass Filter: (CH1-CH4)40Hz –4KHz /(CH5)50Hz –250Hz
- High Pass Filter: 15Hz – 4KHz
- Subsonic Filter: 15Hz - 55Hz
- Full IC-Controlled Protection Circuitry
- Remote Dashboard Subwoofer Control
- Fully Adjustable 12dB Bass Equalizer
- Mute and Delay Soft Start System
- 8 Volt Preamp Circuitry
- Status Mode LED Indicator
- Minimum THD at Rated Power: < 0.05%
- S / N Ratio: >90dB
- Frequency Response: 15-35KHz
- Damping Factor: >100@ 100Hz
- 40 Amp x3
- Dimensions: (W x H x L) 9" x 2.4" x 18.6"
Description of RTR172:
RCA cables are the backbone of your audio system. They are used for transferring audio and video signals. Without a proper cable and good signal, you can have a distortion, which would hold your system back from performing at its optimal capabilities. Don't ever settle for cheap RCA's because they will not provide a clean signal to your amplifiers or video sources.
These Rockville RCA cables are 100 % copper, and feature advanced technologies like triple shielding, magnetic interference rejection, woven outer shield, and more. The best way to ensure that you’ll have a good setup is to invest in good cables.
Features:
- Rockville RTR172 17 Foot 100% Copper 2-Channel Twisted Pair RCA Cable
- Oxygen Free Copper
- 100% Oxygen Free Copper
- Premium Audiophile RCA Interconnect Cables
- Split Pin Technology Ensures a Secure Connection
- Outstanding Noise Rejection, Accuracy, and Frequency Response
- Color Coded Channel Identification
- Length: 17-Foot
- Rockville 1 year warranty
- Also Available in: 3-Foot, 6-Foot, 12-Foot, 20-Foot and 25-Foot
About Rockville Quality Control Procedures:
The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville products are backed with a hassle free warranty.
Video of RWK4CU:
We challenge anyone to put this wire to a resistance test against any other wire on the market with the same gauge. If our cable does not meet or exceed any other cable, even if it costs 3 times more, we will be happy to call tag the item and refund you in full. Why are we so confident ? This cable is 100% copper. You cant have a cable with more than 100 % copper. So the only way a cable would out-perform this one is if it were being advertised as a 4 AWG but they are giving you more wire than advertised. No brands selling 100 % copper cables actually do this.
We guarantee that this kit will compete with the most expensive amp kits
on the market from Kicker, JL Audio, or any other top brands.
Maximum Power!
Looking for a wire kit that has 100% true specifications! A wire kit
that uses 100% copper 4-gauge cable! Then look no further than the
Rockville True-Spec RWK4-CU 4 Gauge Amplifier Wiring Installation
Kit. This package includes everything you'll need to get your amplifier
system powered-up correctly and at peak efficiency. All items included in this kit are top of the line.
The power and ground cables aptly named “Mega Power Cable” is a no
compromise power cable. Rockville’s engineering team over-built and
designed the cables using thousands of strands of only true 100%
oxygen-free, silver-tinned copper strands. The use of a proprietary
special twisting process reduces “surface skin impedance loss” so that
Mega Power cables have zero signal and power loss, delivering full power
from your battery system to your amplifier even at lengths of 20 feet!
The increased current flow and higher amperage carrying capacity will
increase your amplifiers efficiency and keep your amplifier running
cooler. The SuperFlex outer insulating jacket jacket makes installation
and cable routing simple and easy. The 100% copper stranded wire is
extremely tolerant of the hostile conditions found under the hood in
vehicles and compensates for vibration, heat expansion and flexibility.
This flexible and well-shielded wire is crucial for getting through all
of the nooks and passageways within the confines of a vehicle interior.
Some manufactures use all aluminum or mix a little copper with aluminum
to give their cables the appearance of a “heavy-duty” cable. But not
Rockville, our True-Spec 100% oxygen free, silver tinned copper
eliminates corrosion, increases current transfer x 10, and won’t
discolor over time.
The superior quality and materials of the Rockville 100% True-Spec
amplifier installation kit is realized in the included accessories and
cable workmanship. Included is a precision CNC cut full size ANL fuse
housing, machined from solid brass and then 14K gold plated for superior
signal transfer and complete with a matching gold plated 120-amp ANL
fuse. The power cable is wrapped in 6 feet of durable nylon braided
tubing to protect it from heat and chafing in the engine compartment.
All installation accessories such as the ring terminals and spade
connectors are nickel plated for superior signal transfer and
durability.
CRYSTAL SQ AUDIO PLANAR SPEAKER CABLE
The speaker cable included in the Rockville True-Spec is also
manufactured from 100% copper and woven in to a flat planner design and
coated in our Super-Flex insulation so that it fits under and around
your vehicles trim and carpet smoothly and without bulking up. With
crystal clear sound quality these speaker cables deliver true audio
fidelity from your car audio amplifier to your speakers. The 14-gauge
speaker cable included in the 4-gauge kit can handle over 2000 watts of
power without heating up or degrading signal quality.
CRYSTAL SQ RCA AUDIO INTERCONNECT CABLE
Designed and engineered to be the best sounding, best performing and
best looking RCA cables available today. Each channel in the RCA cable
is triple shielded first with dielectric internal insulators and then
with a 98% coverage woven shield. All cables are manufactured of 100%
oxygen free copper and feature twisted pair technology for superior
noise rejection and pure sonic signal flow. The RCA plugs are shielded
metal and feature a spiral cut outer ground ring with center split pin
for precise and tight audio connections. The result of all this
technology is noise free-noise rejection signal transfer for optimum
sound quality. You will hear the difference these RCA signal transfer
cables will make.
- Rockville RWK4CU 4 Gauge 2 Channel Complete Car Amplifier Installation Kit 100% Pure Copper RCA Cables
- 4 Gauge Power Amplifier Installation Kit
- Designed specifically for car audio systems over 1000 watts RMS to 2000 Watts
- Made from silver-tinned 100% virgin copper for a pure uninterrupted transfer of power and signal
- The solid brass gold plated Mini ANL Fuse Holder offers ideal protection for high powered systems
- Strand Count: 1862
- BC-5W2 Compliant
- 17 ft. Frosted Blue 4 gauge power wire with seamless crimp ring terminal
- 3 ft. Frosted Gray 4 gauge ground wire
- 17 ft. Blue 18 gauge remote lead wire
- 25 ft. Frosted Clear/Blue 14 gauge flat speaker wire
- 17 ft. Triple shielded twisted pair RCA cables
- One Mini ANL Fuse Holder with 120 amp ANL fuse
- One 1/2“ black rubber firewall grommet
- One 4 gauge spade terminal
- Two black 12 gauge nickel-plated spade lugs
- Three blue 12 gauge nickel-plated spade lugs
- One black 4 gauge ring terminal
- Ten 6” black zip ties
- UPC:
- 613815913832
