- (1) Power Acoustik MOFOS-12D2 12" 2500 Watt Car Audio Subwoofer DVC 2-Ohm Sub
- (1) Rockville KRYPTON-M1 2000w Peak/500w RMS Mono 1 Ohm Car Amplifier Amp+Remote
- (1) Rockville RWK41 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's
- (1) Rockville RMS12 Single 12" Sealed 1.6 CU FT Car Sub Enclosure Box 3/4" MDF
- (1) Complete Single Sub Box Enclosure Installation Kit: Speaker Wire, Screws, Spades
Description:
MOFO Type S subwoofers are refined and increase efficiency dramatically! MOFO Type S subs use a composite sandwich cone with a polypropylene surface for durability and Spruce pulp backing for smooth low bass. Like the original MOFOs, the new models still use an aluminum dust cap that couples to the voice coil former and extends over the cone. Why? The fins brace the cone and eliminate cone flex during high excursion. And since they are aluminum and couple to the voice coil, they act as a heatsink or heat extractor. Using the latest materials, the new MOFO subs yield superior performance. Cast aluminum baskets? Of course! Increased bottom octave output? You Bet! Louder than the original design? Duh!!
Features:
- Overcompensating Motor Structure for Increased Magnetic Strength
- 12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics
- Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up
- Die-Cast Aluminum Heat Sink Dust Cap Absorbs Voice Coil Heat
- Aluminum Dust Cap Fins Dissipate Heat & Strengthen Cone
- Non-Magnetic Non-Resonate Die-Cast Aluminum Frame
- 2.5” 4-Layer Voice Coil w/ Large Gauge Wire Increases Power
- High-Temperature Tolerance Adhesives Resist Thermal Failure
- Nickel Plated 8ga Spring-Loaded Compression Wire Terminals
- Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection
- High-Density Polyether Foam Surround w/ UV & Chemical Protection
- Dual Poly-Cotton Suspension Dampen Violent Accelerations
- Stitched Voice Coil Leads Prevent Potential Damage
- 1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Included
Specifications:
- Efficiency (1w/1m): 86.40
- Voice Coil Configuration: 2.50″ Dual 2Ω
- Motor Volume: 254oz
- Re: 3.850Ω
- Fs: 27.38Hz
- Qes: 0.383
- Qms: 5.443
- Qts: 0.357
- Diameter: 12”
- Vas: 1.55ft3
- Bl: 20.13tm
- Mms: 219.677g
- Cms: 138.664
- Sen: 86.35db
- MAX Power: 2,500w
- RMS Power: 1,200w
- Cutout Diameter: 11”
- Mount Depth: 6.25”
- Weight: 16lbs.
Enclosure Dimensions
Included in this manual are a number of different enclosure suggestions. These are by no means the only enclosures to use, but they provide a starting point to determine the correct enclosure for your needs many factors must be addressed (amount of power, vehicle, placement, crossovers, etc) Therefore, as al-ways, Power Acoustik recommends that your subwoofer be installed by an authorized Power Acoustik dealer.
Enclosure Construction
All enclosures should be made of .75” (3/4”) material only. When possible, make the baffle 1.5” (1 ½) thick and add .75” (3/4”) to the depth of the enclosure to compensate. All volumes INCLUDE vent/port and subwoofer displacements. DO NOT change the volume unless you plan on adding a substantial amount of bracing. For added performance, applying a coat of fiberglass resin to the interior walls will greatly improve sealing the enclosure. Adding a thin layer of poly-fill will improve response by smoothing out reflections within the enclosure.
Sealed Enclosure Recommendations
- Min: 1.25 cu ft.
- Optimum: 1.50 cu ft
Ported Enclosure Recommendations
- Min: 2.00 cu ft
- Port WxL: 4” x 11”
- Tuning: 34 Hz
- Opt: 2.50 cu ft
- Port WxL: 4” x 13.75”
- Tuning: 30Hz
Krypton Series (Product Video):
What's in the Box:
- Amplifier
- Bass Remote with clipping indicator
- Birth sheet with tested power
- Owner’s manual
- Mounting Screws
- Warranty
Description:
The Krypton series of amplifiers by Rockville are engineered to be reliable and are packed with features. Whether you are a car audio competitor or just like to enjoy loud music we engineered and designed these amps from the ground up to give you great sound quality. You will notice the cool battery voltage display meter which looks great but also serves as a tool for you to know if your battery voltage is dropping which would affect your systems performance. We designed the amps to be able to last for many years even if you are playing them at max volume before clipping for extended periods of time.
Our favorite feature of the Krypton series is the bass remote that has a clipping indicator. This allows you to set the amp to max output before clipping on any song. This will protect your subs while you maximize SPL. What is nice about this is that you can set the gain level to max before clipping on any given song in real time! If you use a DD-1 or another tool, you are setting the gain on one song but the next song might have more headroom or might clip depending on the levels it was recorded at (this is referred to as crest factor in the engineering world).
We guarantee that this series of amplifiers will not only meet their Dyno Certified power but exceed their rated power.
Another feature we love about this is the bass equalizer. Most amps have this feature however not all bass EQ's are created equal. Some bass EQ's will just clip your subs to death. Our bass EQ circuitry will boost the proper frequencies in a way that sounds good and is safe for your subs. In addition you can always use the clip indicator on the bass remote to make sure you are not sending a clipped signal to your subs. Our amplifier is meant to give as much clean power to your subs as possible. Our voltage display allows you to make sure you are getting the proper voltage to your amp and our clip indicator on the remote will make sure you always send clean power to your subs. In addition we also guarantee the amplifier will output over the Dyno Certified so you can confidently match our amplifier with high-end subs and know what to expect!
What about sound quality and efficiency ??
This amplifier is engineered so well that it has an extremely low signal to noise ratio which means the sound will be super clean even at high volume levels. It also has a great efficiency rating so you don't have to draw too much power from your battery. We engineered this to have a high common mode rejection rating (CMRR). This means that the amp has the capability to block out engine noise signals. By rejecting unwanted noise the end result is the cleanest sound quality.
Once again, Rockville has stepped up its game with the all new Krypton series. Their is no other amp like it on the market. The all new Phenom V2 series is in our opinion the best series of amps for the price. Between the true power, the build quality, and the features, we are confident you will agree.
Features:
- Rockville KRYPTON-M1 2000w Peak/500w Dyno-Certified RMS Mono 1 Ohm Car Amplifier Amp+Remote
- Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
- 1 Ohm:500 Watts x 1 Channel <1% THD+N (71% efficient)
- 2 Ohm: 350 Watts x 1 Channel <1% THD+N (81.8% efficient)
- 4 Ohm: 200 Watts x 1 Channel <1% THD+N (85.7% efficient)
- Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
- 1 Ohm: 2000 Watts x 1 Channel
- 2 Ohm: 1400 Watts x 1 Channel
- 4 Ohm: 800 Watts x 1 Channel
- Digital Voltage Display on Amp (Accurate within 0.15V)
- Power/Protect/Clip LED Indicators on the front panel
- Power/Protect/Clip LED Indicators on Remote control
- Clip indicator on the bass remote allows you to quickly set any song to right before clipping in real time
- Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
- Low Pass Filter: 50Hz - 250Hz
- Subsonic Filter: 15Hz - 55Hz
- Fully Adjustable 12dB Bass Equalizer
- Remote Dashboard Subwoofer Control with Clipping Indicator
- 8 Volt Preamp Circuitry
- Phase Control Switch
- High-Speed MOSFET Power Supply
- Optical Coupler Class “D” Technology
- Full IC-Controlled Protection Circuitry
- Mute and Delay Soft Start System
- RCA Preamp Line Output
- Status Mode LED Indicator
- Minimum THD at Rated Power: <0.1%
- S / N Ratio: >90dB
- Frequency Response: 15Hz - 250Hz
- Damping Factor: >150 @ 100Hz
- 1x 60A Maxi Fuse
- Passes the Signal Burst Test (Instant signal for full power “SPL Contest”)
- Rockville engineered with a super low signal to noise ratio to give you clean sound
- Improved Bass EQ filter works well to boost the proper frequencies
- Dimensions: (W x H x L) 12.2˝ x 8.66˝ x 2.2˝
Video of RWK41:
Unboxing Video for RWK41:
Description:
The Rockville RWK41 4 AWG (American Wire Gauge) amp kit has the following differences over other amp kits on the market at this price point.
1. Our RCA cables are 100 % copper. These are top of the line RCA cables
2. Better Resistance: The only thing that really matters with wires is the resistance rating. This is a measurement of conductivity and how much signal is loss per foot of wire. Since Rockville wires are made with around 3 times as much copper as any other wire at this price point, these wires had a much better resistance rating which means they will transfer more power to your amps than the other brands.
3. We do not cheat you on the thickness of the wire. These are standard American wire gauge thickness. This is another reason our conductivity is better than anything else at this price point. Other brands in the market place write 4 gauge, but cheat you on the thickness. We are honest about the thickness.
4. The Rockville amplifier installation kits feature a new soft abrasion proof insulating jacket. This rugged PVC outer jacket allows for 100% improved flexibility over standard power cables making them extremely easy to route through your vehicles interior, and it maintains exceptional resistance to grease and oil. The PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F.
The RCA signal transfer cables included in this kit feature blue and silver twisted pair technology in a clear outer jacket insulation skin. Not only do the blue and silver wires look cool but they also provide superior signal transfer with maximum noise suppression. They are 100% copper to provide absolute lossless perfect signal transfer to your receiver. This technology reduces interference, so your audio signal flows clean and pure at all power levels.
This kit also includes a massive 60 Amp AGU Gold Plated Fuse, so you can be sure it will handle the all the DC power that your amp will need without even the slightest loss of current. The included 7 split loom tube provides protection for your power cable from the typically harsh environment found under the hood of your car.
Audiosavings product experts have tested this amp kit against many leading amp kits on the market and were were impressed not only by the great looks but by the quality of these Rockville installation kits as well. These kits had a lower resistance rating than the other brands we compared and tested them against. What this means is that Rockville manufactures their kits with more copper than other kits at this price point, ultimately providing your amplifiers with better and cleaner DC power, so they work cooler and more efficiently. You will hear the difference a Rockville installation kit will make!
Features:
- 1 – 17’ High Grade Twisted Pair of 100% Copper RCA Cable
- 17’ – 4 Gauge Translucent Blue SuperFlex Power Cables
- 17’ – 18 Gauge Blue Remote Cable
- 17’ – 16 Gauge Clear Speaker Wire
- 3’ – 4 Gauge Clear SuperFlex Ground Wire
- Gold Plated AGU Heat Resistant Fuse Holder
- 60 Amp AGU Gold Plated Fuse
- 7’ Split Tube Loom
- Accessories Included: Wire Ties, Ring Terminals, Butt Connectors, Spades, and Grommets
Description:
The RMS12 is a single 12" sealed speaker box is made in the USA with Grade “A” ¾” MDF wood. This enclosure is 1.6 cubic feet and is compatible with bigger subwoofers that require a lot of air space. This is a very hard to find enclosure size. Most brands do not make this size. We specially made these because we had lots of subwoofers that were big and loud but there were no enclosures on the market that accommodated the requirements of them.
This enclosure is made with precision cutting machinery by industry experts that have been making these enclosures in the USA for over 20 years. All Rockville enclosures come with a customized enhanced glue that is unmatched by any other manufacturer. That means that the carpet will stay in place and not rip or tear. The ¾” USA MDF is much stronger then any type of import wood. This will keep your box performing at an optimal level by not flexing and distorting your woofers. Your woofers will thank you! EVERY Rockville enclosure is not only glued at all joints but stapled as well. If that wasn’t enough we add a layer of silicon to every seam! This makes your Rockville enclosure rock even more!
MADE IN THE USA WITH PRIDE!
Features:
- Rockville RMS12 Single 12" 1.6 cu. ft. MDF Sealed Subwoofer Enclosure
- Single 12" Sealed
- Machine precision cut mounting holes
- ¾” USA Heavy Duty MDF Construction
- Top of the line Glue for extra durable adhesion
- High quality GOLD spring loaded terminals
- Designed, tested, and engineered to work with most of today’s popular woofers. These enclosures are built with the quality additives needed to maximize the performance of any sound system.
- Designed to give the best sound quality
Enclosure Measurements:
- Type of Enclosure: Sealed
- Enclosure Sub Size: Single 12"
- Dimensions in Inches: 18" L x 16" W x 13.25" H
- Top and Bottom Depth: NA"
- Mounting Depth: up to NA" (enough depth for any sub on the market)
- Gross Volume Per Sub (Measurement for the outer dimensions of the box): 2.02 Cubic Feet
- Net Volume Per Sub (Measurement for the outer dimensions of the box less the thickness of the wood): 1.6 Cubic Feet
About Rockville Quality Control Procedures:
The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville sub enclosures are backed with a full 90 day warranty, though it is unlikely that you will need to use it.Complete Single Subwoofer Enclosure Installation Kit!
Includes:
- 10 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
- 12 Feet of 14 AWG Blue Speaker Wire
- 2 Spade Terminals
This accessory package includes everything you need to install one subwoofer into an enclosure, and wire to connect the enclosure to your amplifier. This package is a top of the line accessory package which we put together and tested.
The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure. The speaker wire is 14 gauge. This is way better than using 16 gauge. You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire. These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly.
- UPC:
- 613817051594
