- (1) Power Acoustik MOFO-102X 10" 2400 Watt Car Audio Subwoofer DVC 2-Ohm Sub
- (1) Rockville RQB10 Single 10" Vented Ported Subwoofer Sub Box Enclosure 1.4 cu ft
- (1) Complete Single Sub Box Enclosure Installation Kit: Speaker Wire, Screws, Spades
Description:
MOFO-X subwoofers are refined and increase efficiency dramatically! MOFO subs use a composite sandwich cone with a polypropylene surface for durability and Spruce pulp backing for smooth low bass. Like the original MOFOs, the new models still use an aluminum dust cap that couples to the voice coil former and extends over the cone. Why? The fins brace the cone and eliminate cone flex during high excursion. And since they are aluminum and couple to the voice coil, they act as a heatsink or heat extractor. Using the latest materials, the new MOFO subs yield superior performance. Cast aluminum baskets? Of course! Increased bottom octave output? You Bet! Louder than the original design? Duh!!
Cast Aluminum Heatsink
Cast Aluminum Heatsink
The anodized blue dust cap on the MOFO subwoofer looks cool and also serves a specific purpose. Because the dust cap is coupled to an aluminum voice coil former, it acts as a heatsink, extracting heat away from the voice coil, keeping it cool.
Non-Pressed Pulp Cone
Non-Pressed Pulp Cone
Ask any sound quality enthusiast what woofer cone material they prefer, and they will all say PAPER. With that in mind, we used a beefy non-pressed pulp paper cone. The aluminum dust cap fits into the recesses of the cone for additional bracing.
Features:
- Overcompensating Motor Structure for Increased Magnetic Strength
- 12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics
- Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up
- Die-Cast Aluminum Heat Sink Dust Cap Absorbs Voice Coil Heat
- Aluminum Dust Cap Fins Dissipate Heat & Strengthen Cone
- Non-Magnetic Non-Resonate Die-Cast Aluminum Frame
- 2.5” 4-Layer Voice Coil w/ Large Gauge Wire Increases Power
- High-Temperature Tolerance Adhesives Resist Thermal Failure
- Nickel Plated 8ga Spring-Loaded Compression Wire Terminals
- Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection
- High-Density Polyether Foam Surround w/ UV & Chemical Protection
- Dual Poly-Cotton Suspension Dampen Violent Accelerations
- Stitched Voice Coil Leads Prevent Potential Damage
- 1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Included
Specifications:
- MAX Power: 2,400 Watts
- RMS Power: 1,200 Watts
- Impedance: DVC 2Ω
Enclosure Recommendations
All enclosures should be made of .75” (3/4”) material only. When possible, make the baffle 1.5” (1 1/2”) thick and add .75” (3/4”) to the depth of the enclosure to compensate. All volumes INCLUDE vent/port and subwoofer displacements. DO NOT change the volume unless you plan on adding a substantial amount of bracing. For added performance, applying a coat of fiberglass resin to the interior walls will greatly improve sealing the enclosure. Adding a thin layer of poly-fill will improve response by smoothing out enclosure.
Sealed Enclosure
- Cubic Feet: 0.75
- Tuning Frequency: 49.7
Ported Enclosure
- Cubic Feet: 1.25
- Port Diameter: 3" x 11.5"
- Tuning Frequency: 31.1
Driver Parameters
- FS (Hz): 26.71
- QMS: 4.45
- VAS (ft3): .908
- X-MAX (mm): 15
- X-MECH (mm): 21
- QES: .33
- RE (Ω): 3.84
- BL (Tesla): 21.22
- RMS Power: 1,200w
- MAX Power: 2,400w
- QTS: .31
- SPL (1w/1m dB): 83.6
- Voice Coil: DVC 2Ω
Physical Dimensions
- Overall Diameter: 10.75”
- Overall Height: 7.00”
- Mounting Depth: 6.125”
- Cutout Diameter: 9.00”
- Motor Diameter: 7.125”
- Motor Height: 2.625”
- Flange Width: 0.75”
- Flange Height: 0.50”
- Weight: 21LBS.
Features:
- Rockville RQB10 Single 10" Vented Ported Subwoofer Sub Box Enclosure 1.4 cu ft
- Single 10" Side Ported
- Finished with Durable Bed Liner<
- 3/4" MDF
- High Quality Spring Loaded Terminal
- Air Space: 1.4 Cubic Feet
- Tuning Freq- 39Hz
- Mounting Depth: 8"
- Height: 11"
- Width: 20"
- Depth: 14"
- Cutout diameter: 9.185"
Complete Single Subwoofer Enclosure Installation Kit!
Includes:
- 10 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
- 12 Feet of 14 AWG Blue Speaker Wire
- 2 Spade Terminals
This accessory package includes everything you need to install one subwoofer into an enclosure, and wire to connect the enclosure to your amplifier. This package is a top of the line accessory package which we put together and tested.
The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure. The speaker wire is 14 gauge. This is way better than using 16 gauge. You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire. These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly.
- UPC:
- 613817050955
