Package Includes:

• (1) Rockville KRYPTON MT1 1600w 2 Channel Marine/Boat Amplifier w Volt Meter
• (1) Rockville RMWK4 4 AWG Gauge Waterproof Marine Amplifier/Amp Install Wire Kit

---

How To Install a Marine Amplifier onto Your Boat:

VIDEO OF KRYPTON MT1:

What's in the box:

• Amplifier
• Birth sheet with tested power
• Mounting Screw Kit
• Warning Instruction
• Warranty
• Owner’s manual?

Description:

We took the sound of our Krypton car amps and we added top of the line marine grade parts so that they will withstand even the harshest conditions on the water.

We went a little overboard (no pun intended) to make this amp marine ready. We conformal coated the PCB board with a waterproof glue that is painted on to protect the circuitry. The heat sink including the bottom plate is made of aluminum which is rustproof. The end panels, internal mounting screws and hardware of the amp are made of stainless steel and are rustproof. Even after many years of use the amp will be rust free and operate like new!

The KRYPTON MT1 is a class AB 2-Channel high power amplifier with 1,600 watts peak output and 400 watts dyno-certified RMS power. The peak rating can be used to compare with brands who use peak ratings such as Boss and Power Acoustik while the Dyno Certified RMS rating can be used to compare with top brands such as Kicker, Rockford, Alpine, etc.

This amp has a very cool fully adjustable 12dB/Octave crossover. What is cool about it is that our crossover supports low pass, high pass, bandpass, and subsonic. This makes our amp ideal for subwoofers (sealed and vented), full range speakers, and midrange speakers. In high pass mode we allow you to filter out frequencies between 15Hz - 4KHz. In full mode you will not be filtering any frequencies. The really cool part is in low pass mode you can use the high pass and low pass mode. So for example you can set the low pass mode to 50 hz, and then you can set the high pass to 15 Hz. In this case you would be playing frequencies in the range of 15-50 Hz on this channel. This would be an example of using the subsonic filter. Another option you have is for midrange speakers, you can use our low pass filter and set it really high. Lets say to 3Khz and then you can set the high pass to 150Hz and your midrange speakers will only play that frequency range. Our advanced crossover technology will allow you to really fine tune each speaker to get the sound you desire.

The KRYPTON MT1 is protected by a fully IC controlled circuit which includes mute, delay, and soft start technology so that the amplifier will turn on safely every time and protect your speakers from popping.

You will also notice we decided to add a cool battery voltage display meter which looks great but also serves as a tool for you to know if your battery voltage is dropping which would affect your systems performance. We designed the amps to be able to last for many years even if you are playing them at max volume before clipping for extended periods of time.

This is a class A/B amplifier which is what we recommend to get the best sound quality out of full range speakers.

Features:

• Rockville KRYPTON MT1 1600w Peak/400w Dyno-Certified RMS 2 Channel Marine/Boat Amplifier w Volt Meter
• Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
• 2 Ohm: 200 Watts x 2 Channel <1% THD+N
• 4 Ohm: 120 Watts x 2 Channel <1% THD+N
• 4 Ohm Bridged: 400 Watts x 1 Channel
• Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
• 2 Ohm: 800 Watts x 2 Channel
• 4 Ohm: 480 Watts x 2 Channel
• 4 Ohm Bridged: 1600 Watts x 1 Channel
• Painted Conformal Coated PCB Board (Uses 2577 Waterproof Glue)
• Rustproof Aluminum heat sink with black hairline finish
• Stainless steel end panels are rustproof
• All screws and mounting hardware are stainless steel and rustproof
• Bottom panel is aluminum and rustproof
• Digital Voltage Display on Amp
• High Level Input(Auto ON)
• High-Speed MOSFET Power Supply
• Under Voltage Protection at 10V
• Over Voltage Protection at 16V
• Tertiary Supplies Circuitry
• Studio-Grade Bipolar Output Stage Transistors
• Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
• Low Pass Filter: 50Hz - 250Hz
• High Pass Filter: 60Hz -1.2KHz
• Full IC-Controlled Protection Circuitry
• Fully Adjustable 12dB Bass Equalizer
• Mute and Delay Soft Start System
• RCA Line Output
• 8 Volt Preamp Circuitry
• Status Mode LED Indicator
• Minimum THD at Rated Power: < 0.05%
• S / N Ratio: >90dB
• Frequency Response: 10Hz - 50KHz
• Damping Factor: >100 @ 100Hz
• 25 Amp x2 ATC Fuse
• Dimensions: (Lx W x H) 12.4" x 8.7" x 2.2"

---

Video of RMWK:

Features:

• Rockville RMWK4 4 AWG Gauge Waterproof Marine/Boat Amplifier Wire Installation Kit
• 20 ’ Translucent, Twisted Pair, High Quality, Tinned-OFC Flexible PVC RCA Cable
• 18’ 4 Gauge High Current, Low Impedance, Clear Flexible Power Cable with 3’ Black Poly Woven Mesh to better resist chemicals in the battery compartment
• 18’ 4 Gauge High Current, Low Impedance, Light Blue, Flexible Ground Cable
• 25’ 16 Gauge 100% Tinned-CCA, White, Non-Transparent Resin PVC, Flat Speaker Cable
• 25’ Blue Remote Wire
• (1) Silver Mini-ANL Fuse Holder – Clear Shell and Clear Blue Bottom Bracket with Blue Waterproof Ring
• (1) 120A Mini-ANL Fuse
• (1) 80A Mini-ANL Fuse
• (2) Ring Terminals
• (2) Spade Terminals
• (5) Speaker Cable Terminals
• (1) Washer
• (10) White Cable Ties