- (1) JBL CSMA280 Commercial/Restaurant 2 x 80w Amplifier 4ohm/8ohm/70V/100V, 8 inputs
- (2) Pair of JBL Control 25-1 5.25" 30w 70v Wall-Mount Commercial Restaurant/Bar Speakers
- (2) Pairs of JBL 8128 8" Full Range Commercial 70V/100V 6w Ceiling Speakers 4 Restaurant
Video of CSMA280 :
Description of CSMA280:
Designed for commercial and industrial use, the CSMA 280 Commercial Series Mixer/Amplifier from JBL is a mixer/amplifier with eight mixer-channel inputs and two output channels. It's capable of reaching 80W of peak power with 10W per channel. The unit's front panel sports volume controls for each channel, as well as two master volume adjustment knobs, two sets of bass and treble controls, and a power switch. The volume controls are illuminated so they can be seen and operated in darkened environments.
The amplifier, capable of driving both eight and four Ohm loads, can be used with 70V and 100V distributed audio systems without the need for a separate transformer. On its back panel you'll find euroblock connections for mic/line inputs, as well as unbalanced RCA inputs, speaker connections, dip switches for input routing, and more. The unit is also equipped with two RJ45 connectors for use with JBL CSR-V in-wall volume controls (available separately).
This Commercial Series mixer/amplifier boasts such features as voice activating ducking (useful for paging over background music), priority muting for channels one and five, and a sleep mode which automatically powers down the unit when no audible signal has been received for longer than 30 minutes. Also, with two auxiliary outputs, you may connect to an additional amplifier, though the master volume and tone controls will have no bearing on the resulting signal.
Channel Modes
8 inputs with 2 outputs of 80W of power.
Controls
Independent Bass and Treble controls for each output channel.
Input level and output volume controls.
Hi-Z Switch
The Hi-Z switch will switch in the built-in output transformer allowing the unit to drive 70V or 100V speaker systems directly when connected to the appropriate output terminals.
Phantom Power
Phantom power (27 V) can be applied to all mic inputs by turning on Phantom Power within the dip switches.
VOX Function
Voice activated ducking is available on input channel 1 and channel 5. The audio input level required to activate ducking is set using the trim pot on the rear panel. Adjusting in the counter-clockwise direction will reduce that level, while the full clockwise setting will disable the VOX function.
Priority Muting
Channels one and five may be used as priority channels, muting all other channels when pins 4 and 5 are shorted using a switch closure. If the amplifier has entered sleep mode due to inactivity, invoking priority will also bring the unit out of sleep and ready for transmitting an announcement.
Remote Volume Control
Remote volume control can be implemented using a CSR-V controller connected via an Ethernet cable to the RJ45 connector on the back panel.
Sleep Mode
This unit is designed to go into sleep mode after approximately 30 minutes operating with no signal at any of the inputs. Return of signal (-40 dBu or 7.75mVRMS) to any input will wake the unit. Also, a switch closure across the priority input pins will return the unit to normal operating mode.
AUX output
An auxiliary output that you may connect to additional amplifiers is available. The audio signal is the mix of the input channels. Note that the master volume control and tone controls will have no effect on the aux output signal.
Manufacturing
Crown's DriveCore technology
HARMAN's GreenEdge environmental standards
Certifications and Approvals
Lead-free RoHS standards, utilizing recycled metals, and using an energy-saving powder coat process
Energy Star certified
Features:
- JBL CSMA280 Commercial/Restaurant 2 x 80w Amplifier 4ohm/8ohm/70V/100V and 8 inputs
- For Commercial and Industrial Use
- 80W into 8 or 4 Ohm Loads
- 10W Per Channel
- 8 Input Channels, 2 Output Channel
- Usable with 70 & 100V Systems
- Euroblock Mic/Line & RCA Inputs
- Hi-Z & 27V Phantom Power Switches
- Sleep Mode & 2 Auxiliary Outputs
- Voice Activated Ducking & Priority Mute
Specifications:
- Maximum Output Power: 800 W per channel into 4 Ohms or 8 Ohms, 1 kHz, ≤ 0.5% THD
- Insertion Loss: 1 dB maximum for 70 and 100 V outputs
- Continuous Power: 10 W per channel
- Line Output Level: 5.0 V RMS into 10 kOhms
- Input Sensitivity: To obtain full rated power at 8 Ohms (or 5 VRMS to line output). Mic Input: 3 mV RMS. Line Input: 775 mV RMS. RCA Input: 300 mV RMS
- Number of Channels: Input: 8, Output: 2.
- Frequency Response: Measured at 2.83 V RMS into rated load impedance at any output. 4/8 Ohms Output: 20 Hz - 20 kHz, ±2 dB. 70 V/100 V Outputs: 80 Hz - 15 kHz ±2 dB. Line Out: 20 Hz - 20 kHz, ±1 dB
- Total Harmonic Distortion (THD): Measured at 2.83 V RMS into rated load impedance at any output. Power Amplifier Output: <0.5%, 20 Hz to 20 kHz. Line Output: 0.05% typical
- Signal to Noise Ratio: > 90 dB
- Nominal Input Impedance: Mic: 400 Ohms. Line: 20 kOhms (balanced). RCA: 50 kOhms.
- Minimum Load Impedance: Low Impedance Output: 4 Ohms. 70 V Output: 120 Ohms. 100 V Output: 240 Ohms.
- Crosstalk: -70 dB @ 1 kHz
- Controls:
- Front Panel:
- 8 x Input level rotary knobs
- 2 x Output volume-attenuating knobs
- 1 x Power switch
- 2 x Bass potentiometers
- 2 x Treble potentiometers
- Rear Panel:
- 2 x Input-routing dip switches (including phantom and Hi-Z switches)
- 8 x Mic/Line selector switch
- 2 x Vox adjustment switches
- Indicators:
- Front Panel:
- 8 x Input signal presence ring, green
- 2 x Output volume ring, green
- 1 x Power switch ring, green/blue
- Connectors:
- Rear Panel:
- 1 x IEC power input
- 2 x Aux out connection points
- 6 x 3-pin euroblock connectors
- 6 x 3-pin euroblock connectors
- 2 x 5-pin euroblock connectors
- 6 x Dual RCA input connectors
- 2 x RJ45, remote volume
- Operating Temperature / Humidity: 32 to 95°F / 0 to 35°C, 95% RH (non-condensing)
- Storage Temperature: -4 to 185°F / -20 to 85°C
- Phantom Power: 27 VDC
- AC Input: 100-240 VAC, 50/60 Hz
- Dimensions (W x D x H): 17.2 x 11.9 x 1.7" / 436.9 x 302.3 x 43.2 mm
- Weight: Approximately 11.9 lb / 5.4 kg
Authorized JBL Dealer!
Video of Control 25-1-WH :
Description:
Designed by JBL, these Control 25-1 loudspeakers are two-way 5.25" indoor/outdoor monitors featuring weather-protected circuitry, natural and powerful representations of the frequency spectrum, white enclosures, and JBL's proprietary InvisiBall mounting hardware. This hardware allows you to install the speakers through a hidden access point behind its logo badge. As such, the Control 25-1 suitable for venues, health clubs, theme parks, cafes, or anywhere where foreground/background music—and paging—is a necessity.
These monitors are capable of handling 200W of programmatic material at 8 Ohms, and feature a built-in multi-tap transformer for operation on distributed speaker lines. With an SPL of 110 dB, you can blast these speakers pretty loudly as well, while their cone geometry ensures a pleasurable listening experience in both on- and off-axis situations. Additionally, their PEI diaphragms render a smooth high-frequency response. But sound is not the only consideration: Kapton voice coil formers, JBL's WeatherEdge rubberized extensions, and a durable cabinet construction provide protection against heat, rain, wind, or anything else the elements might throw at you in the coming years.
Also, while the Control 25-1 comes in a white finish, it doesn't have to stay that way: these speakers accept a variety of finishes and pigments to match any surrounding.
Features:
- 2 JBL Control 25-1 5.25" 100w White Surface-Mount Speakers 4 Home/Restaurant/Bar
- 5.25" Woven-Fiberglass LF Drivers
- 0.75" PEI Diaphragm Tweeters
- 200W RMS at 8 Ohms
- Durable, Weatherized Enclosures
- InvisiBall Mounting Hardware
- Zinc-Plated Grilles
- Good for Off-Axis Listening
- 60 Hz to 20 kHz Frequency Response
Specifications:
- Power Rating: 200 W continuous program (2 h). 100 W (400 W peak), continuous pink noise (2 h). 75 W (300 W peak) continuous pink noise (100 h)
- Nominal Impedance: 8 ohms (THRU setting)
- Maximum Input Voltage: 25.3 V RMS (2 h), 50.6 V peak
- Frequency Response ± 3dB: 85 Hz to 17 kHz
- Frequency Response ±10 dB: 60 Hz to 20 kHz
- Sensitivity: 90 dB, 1 W / 1 m (average 100 Hz to 10 k Hz)
- Coverage Angle: 100° x 100°
- Directivity Factor: 6.0 (averaged 1 kHz to 16 kHz)
- Directivity Index: 7.6 dB (averaged 1 kHz to 16 kHz)
- Crossover Type: 2nd order low-pass, 2nd order high-pass
- Transformer Taps: 70 V: 30 W, 15 W, 7.5 W, 3.7 W, 100 V: 30 W, 15 W, 7.5 W. Insertion loss < 0.94 dB at any tap setting. Thru setting: 8 Ohms nominal
- Recommended Protective High-Pass: 60 Hz high-pass (24 dB/oct) (for 8 Ohms operation and for all 70 V / 100 V taps settings)
- LF Driver Size: 5.25" / 135 mm
- HF Driver Size: 0.75" / 19 mm
- Driver Type: LF Driver: Woven-fiberglass cone with pure butyl rubber surround with Weather-Edge frame protection, high-temp Kapton voice coil former, high-temp voice coil wire, optimized cone geometry, linear suspension spider, and FEA optimized motor structure. HF Driver: PEI diaphragm, low-viscosity ferro-magnetic fluid, and Kapton voice coil former
- Enclosure Material: High-impact polystyrene (HIPS)
- Grille: Highly zinc-plated, finished in durable TGIC polyester powder-coating
- Termination: Screw-down terminal strip, zinc-plated copper based, nickel-plated metal screws and washers. Accepts up to 9 mm outside 4 mm inside open lugs (#6, #8, or #10 lug), plus bare wire (up to 12 AWG / 2.5 mm2)
- Environmental: IP-44 per IEC529; exceeds MilSpec 810 for humidity, salt-spray, temperature & UV; passes MilStd-202F for salt spray and ASTM G85 for acid-air plus salt spray
- Agency Rating: ROHS-compliant; Transformer UL Recognized per UL1876
- Dimensions (H x W x D): 9.6 x 7.4 x 5.7" / 243 x 188 x 145 mm
- Weight: 7.5 lb / 3.4 kg
- Package Weight: 18.0 lb
- Box Dimensions (LxWxH): 16.0 x 11.75 x 11.4"
Authorized JBL Dealer!
Video of 8128 :
Description:
8-inch, Full-Range,
In-Ceiling Loudspeaker
The 8128 is a 8-inch, full-range, cost-effective loudspeaker for commercial
applications. The 8128 features high-fidelity performance in an easy to install
package. The system’s high sensitivity drivers deliver maximum sound levels
using minimal amplifier power. With its contemporary grill design, 70V/100V taps
and an open-back design, the 8100 series brings elegance and performance to
basic commercial sound systems, or any application not requiring a back can for
installation.
Features:
- (4) JBL 8128 8" Full Range 70V/100V 6 Watt Commercial Ceiling Speakers for Restaurant/Bar/Cafe
- Component: 8" Full-Range Driver
- Frequency Range: 50 Hz – 16 kHz
- Sensitivity: 97 dB
- Coverage: 90° Conical
- 70V/100V Taps: 6W, 3W, 1.5W (0.75W at 70V only)
- Termination: Bare Wires
- Clear, High-Fidelity Performance
- Dog-ears for easy Blind Mount Installations
- High Sensitivity (93 dB, 1W, 1m) for Maximum Power Efficiency
- 6W Transformer for use of 70V / 100V Distributed Lines
- Included Accessories: Sculpted Grille
- Product Dimensions (Diameter x Depth): 11.3" x 4.1" inches
- Product Weight: 3.0 Lbs.
- UPC:
- 613815699217
