- (1) Peavey Classic 50 410 2-Chnl 4x10 50 Watt Tube Guitar Amplifier Tweed Combo Amp
- (1) Rockville PRO-M50 Studio Headphones+Detachable Coil Cable+Case+Extra Ear Pad
- (1) Rockville RDS30 Deluxe Thick Padded Foldable Drum Throne Stool
- (2) Rockville RCGT20B 20' 1/4'' TS to 1/4'' TS Instrument Cables-Black
- (1) Peavey PVI100XLR Wired Dynamic Cardioid Vocal Microphone+Case+Mic Clip + Cable
Authorized Peavey Dealer!
Video of CLASSIC 50/410:
Originally launched in 1991, these versatile all-tube amps retain their distinctive sound and circuitry but now feature an updated chassis design. With three 12AX7s up front and four EL84 power amp tubes plus normal and bright inputs, 3-band passive EQ, and presence control, it's all the classic tone you seek and all the gigging versatility you need.
Features:
- Peavey Classic 50 410 Guitar Amplifier Tweed Combo
- Normal and bright inputs
- Four EL84s and three 12AX7s
- 3-band passive EQ
- Presence control
- Normal and lead volume
- Lead pre- and post-gain
- Master volume
- Reverb control
- Effects loop
- Fan cooled
- Chrome-plated chassis
- Tweed covering
- Four 10 inch Blue Marvel® speakers
- Footswtich for channel switching and reverb (included)
- 50 watts (rms) into 16 or 8 ohms
Details:
- POWER AMPLIFIER SECTION
- Four 6BQ5/EL84’s with 12AX7 driver
- Rated Power & Load:
- 50 W RMS into 16 or 8 ohms
- Power @ Clipping (Typically):
- (5% THD, 1 kHz, 120 V AC line)
- 50 W RMS into 16 or 8 ohms
- (Bias must be reduced to measure)
- Frequency Response:
- +0, -2 dB, 50 Hz to 15 kHz, @ 40 W RMS into 16 ohms
- Hum & Noise:
- No greater than 80 dB below rated power
- Power Consumption:
- 200 watts, 50/60 Hz, 120 VAC (Domestic)
- PREAMP SECTION
- Two 12AX7’s
- The following specs are measured @ 1 kHz with the controls
- preset as follows:
- Pre & Post (lead) @ 0
- Reverb Level @ 0
- Bass & Treble EQ @ 12
- Middle EQ @ 0
- Master Volume @ 12
- Presence @ 6
- Nominal level is with Input Gain @ 6.
- Minimum level is with Input Gain @ 12.
- Preamp Normal Input:
- Impedance: Very high Z, 470 K ohms
- Lead Channel (Post Gain @ 10):
- Nominal Input Level:
- -40 dBV, 10 mV RMS
- Minimum Input Level:
- -70 dBV, 0.3 mV RMS
- Normal Channel:
- Nominal Input Level:
- -17 dBV, 140 mV RMS
- Minimum Input Level:
- -28 dBV, 40 mV RMS
- Maximum Input Level:
- 0 dBV, 1.0 V RMS
- Preamp Bright Input:
- Impedance: Very high Z, 470 K ohms
- +12 dB boost @ 2 kHz
- Equalization:
- (Lead and Normal Channels)
- Custom bass, middle, and treble passive-type EQ
- Effects Send:
- Load Impedance: 1 K ohm or greater
- Nominal Output Level: -6 dBV, 0.5 V RMS
- Effects Return:
- Impedance: High Z, 2 M ohms
- Designed Input Level: -6 dBV, 0.5 V RMS
- (Switching jack provides Effects Send to Effects Return
- connection when not used.)
- External Footswitch Function:
- Reverb Defeat (when reverb control is raised)
- Normal/Lead Channel Select (when Lead activated)
Includes:
- PRO-M50 headphones
- Detachable cable
- Soft suede and leather ear cushions (interchangeable)
- Leather hard travel protective case
- Gold plated ¼" adapter
All About Your PRO-M50:
Description:
Rockville brings you studio quality headphones and at an incredible price with its new PRO-M50 headphones. These are professional grade headphones that are guaranteed to ourperform headphones that cost triple the price! These feature ergonomically designed swiveling cups with interchangeable soft suede or leather finish cushions (included). The ear cups seal tight for excellent sound isolation and minimal bleed. Inside these cups you'll find 40mm Neodymium drivers delivering accurate audio with an extended frequency range for clear and rich bass, and a full frequency range of mids and highs. These are closed back style headphones specifically designed for studio monitoring. These play back the sound with a flat frequency curve so you can hear your music exactly how it was recorded. With the PRO-M50 you can expect to hear every detail of every song with extreme accuracy. These headphones cover full frequency ranges; even extending a bit past the frequencies that the human ear can hear.
The headband is made of soft leather, offering ultimate comfort even after extended wear. The beautifully designed stainless steel headband frame and arms are strong and durable. A detachable 51" coiled 100% Oxygen Free Copper cable with a gold plated 3.5mm plug is included along with a gold plated ¼" adapter to ensure the best possible signal. A hard leather case is included to store and protect your new investment when you are on the go.
Amazing sound quality will make these your go-to headphones whether in the studio or out and about!
Features:
- Rockville PRO-M50 Studio Headphones w/ Detachable Coil Cable, Case+Extra Ear Pad
- Professional High-Definition Studio Headphones
- 40mm Neodymium drivers
- Ergonomically designed swivel ear cups
- Supreme sound isolation
- Accurate sound reproduction
- Minimal bleed
- Sturdy and durable steel headband and arms
- Soft leather headband cover
- Interchangeable leather and soft suede ear cups covers included
- Detachable 51" coil cable made of 100% Oxygen Free Copper (158" fully extended)
- Gold plated 3.5mm connector
- Gold plated ¼" adapter
- Hard leather carrying case
- Stainless steel headband frame and moving arms are durable and long-lasting
Specifications:
- Style: Closed-Back
- Design: Circumaural
- Transducer Type: Dynamic
- Driver: 40MM
- Sensitivity: 97±3dB
- Impedance: 32ohm
- Frequency Response:10Hz - 25KHz
- Max. Power: 600MW
- Rating Power: 260MW
- Net Weight: 290g (with cable)
How to Set Up Your RDS30:
Video Of RDS30:
Deluxe
Drum Throne
Check out the new RDS30 from
Rockville. We decided to not bother manufacturing those cheap thrones. We were more interested in quality at a reasonable price rather than just making the cheapest possible throne. One of the main differences between ours and others you will find on ebay are the mechanism. To adjust the seat up and down we have a knob you turn to loosen and then you can pull the pin out and adjust the seat, and then you put the pin in and tighten the knob. Since our throne has a knob you tighten the seat is secure and tight without shaking. The cheaper models on the market only give you a pin without a knob to tighten it. If you have ever used a stand or throne with this mechanism you will notice the shakiness. This cheaper mechanism is not sturdy. We decided to make our throne with only top of the line mechanisms.
This has a collapsible design making it completely portable. This model has 2 knobs. One for adjusting the height of the seat, and the other for adjusting the legs. The metal we use to manufacture these are clean and strong. Our Rockville throne is also double braced for added strength. We upgraded our throne’s padding to a 2.5” thickness, offering hours of comfort.. It makes a big difference when sitting for long periods of time. We covered it with a round vinyl covered cushion. The craftsmanship on this throne is truly great. I compared this unit to units from big famous brands and these are way better and like a third of the price. These are extremely durable.
Shock absorbing molded rubber feet keep the RDS30 from sliding, and the
solid ear casting gives the RDS30 remarkable stability and durability.
The RDS30 is height adjustable from 18.9” to 24.4” so you can adjust it
to meet your exact preferred playing position. This model is as sturdy as a throne can be.
If you want the best quality and best price, buy this throne. There are some out there for around the same price as this Rockville but they are not as good. They have less cushion, a cheap pin mechanism with no handle, and are not double braced. You will not be as happy with those though. This is a premium throne for the same price as the entry level thrones.
Features:
- Rockville RDS30: Foldable Drum Throne
- Deluxe Extra Thick Padding & supportive cushion for fatigue free hours of drumming
- Die-cast seat and thick rubber feet for excellent stability
- Adjustable Height ensures comfortable playing
- Lightweight, stable, and comfortable
- Sturdy tripod base made with solid ear casting
- 11" round seat top, 2.5" thick
- Weight Capacity: 265 lbs.
Video of RCGT20B:
Description:
All Rockville pro audio cables are made with 100% copper which boosts the efficiency of the cable. There is nothing better than 100% copper. Most of the cheaper cables on the market do not use 100% copper, instead they make their cables with CCA (Copper Clad Aluminum). CCA cables do not perform on the level that 100% copper cables perform at. CCA will not conduct signals efficiently. A 12 gauge CCA cable will not even perform as well as a 14 gauge 100% pure copper cable, which will in turn, affect the performance and longevity of your equipment. If you find cables on the market that do not mention the copper content, there is a good chance that they are selling you a cheaper cable that is CCA and not 100% copper. Rockville pays an inspection company to oversee the manufacturing of the product to ensure that we provide a 100% Oxygen Free Copper Cable (OFC). Our OFC cables are less prone to oxidation, and will provide maximum signal transfer.
The other important factor of a cable is the shielding. Most of the good brands on the market have about 85% shielding coverage, so we decided to take our shielding a step further. Rockville cables are shielded with a tight copper mesh, covering 90% of the cable! The high percentage of coverage increases the ability to absorb the Electromagnetic Interference (EMI) and Radio Frequency Interference (RFI) that suppresses signal and degrades the performance of equipment. Rockville Cable’s copper shielding provides great flexibility, maintains a durable structural integrity, while decreasing signal interference ensuring enhanced signal clarity with every use.
Features:
- Rockville RCGT20 1/4'' TS to 1/4'' TS Guitar / Instrument Cable
- 24 AWG 100% Copper Conductors for Enhanced Signal Clarity
- Nickel Plated, 1/4" Straight-to-Same Connectors
- High Density 90% Coverage OFC Braid Shield for Superior EMI and RFI rejection
- Length: 20 Ft
- Color: Black
Description of PVI100XLR:
Peavey PVi100XLR
An economic microphone that comes with Peavey performance and quality that you desire! Dynamic Cardioid design for easy stand-mount application with solid die-cast rugged body, metal mesh grill and black finish.
Features:
- Dynamic cardioid microphone designed for stand-mount application
- On/off switch
- Clean, natural sound
- Low pop and handling noise
- Solid Zinc die-cast body
- Low-gloss black finish
- Includes carrying pouch, mic clip and 6 meter XLR cable
Specifications:
- Frequency Response: 80Hz-12000Hz
- Sensitivity: -53dBV/PA (2.2mV/PA)
- Output Impedance: 500 ohms
- Packed Dimensions(W x H x D): 3.75" x 8.5" x 10.5"
- Packed Weight: 1 lbs.
- UPC:
- 613815969297
