Package Includes:
- (3) Pairs of Rockville RKL80MW 8" 900 Watt White 2-Way Marine Boat Speakers w/LED's
- (1) Rockville DBM65 6-Channel 2600w Peak/660w Dyno-Certified RMS Marine/Boat Amplifier
- (1) Rockville RMWK4 4 AWG Gauge Waterproof Marine Amplifier/Amp Install Wire Kit
- (3) Rockville DMAC80W Dual 7.7" White Aluminum Wakeboard Tower Speaker Enclosure
- (1) Rockville RGHR2 Marine Gauge Hole Receiver w Bluetooth USB, Radio + Wired Remote
Video of RKL80MW:
Includes:
- Pair of 8" Marine LED Speakers
- 16.4 feet of Speaker Wire
- Stainless Steel Mounting Screws
- Pair White Grills
- Pair Rockville RKL80MW 8” 2-Way 900 Watt White Marine Boat Speakers with LED Lights
- Power Rating: 450 Watts Peak /100 Watts RMS Per Speaker
- Total Power Per Pair: 900 Watts Peak / 200 Watts RMS
- Beat sync LED’s flash to the rhythm of the music
- You can select either red or blue color LED’s on the wire harness
- No extra installation for the LED. It gets a power signal through your speaker wire
- The louder the music the more intense the LED’s flash
- IP66 waterproof rating
- Fully Marinized Against Salt & Fresh Water Conditions
- UV treated cone makes this completely Waterproof and rustproof
- Anti-corrosion Stainless Steel Terminals
- Molded ABS plastic for amazing sound and protection from the elements while out on the water
- Polypropylene Formed Cone
- 22 Oz Y30 magnet supports high power handling
- Rubber Surround
- High quality ferrite magnet
- 1” inch PEI Tweeter
- 8” Woofer with Oversized 1.2” CCAW Kapton Voice Coil
- Pre-installed Stainless-Steel mounting screws included
- Perfect for Marine, Car, ATV and UTV applications
- Impedance: 4-Ohm
- Frequency Response: 40Hz - 20KHz
- Sound Pressure Level: 89dB @ 1w/1m
- Total Diameter: 8.07”
- Cutout Diameter: 6.89”
- Total Height: 4.84”
- Mounting Depth: 3.54”
- Perfect for marine, ATV, outdoor use
How To Set Up Your DMAC65 and DMAC80 Wakeboard Tower Speaker Pods:
Includes:
- 1 Double Wakeboard Can
- All mounting hardware
- (2) 2.375” rubber inserts
- (2) 2.25” rubber inserts
- (2) 2.5” rubber inserts
- (2) 2” rubber inserts
Rockville is proud to introduce our all new line of aluminum wakeboard cans. The DMAC80W features double pod design which allows you to mount two 7.7” speakers. It includes our rugged universal aluminum clamp for easy installation to any wakeboard tower pole measuring from 2" to 2.5" diameter. Six precision molded high impact rubber inserts guarantee fitment on towers from 2” to 2.5”. Our clamp inserts are precision-fitted to sit perfectly inside the metal clamps. The speaker terminals are safely enclosed inside the waterproof speaker canister.
***Please note if you need an insert to accommodate a 1.75" diameter tube please let us know and we will send one out to you free of charge!
This awesome double pod is built of super strong aircraft grade 6061 aluminum. The DMAC80W features a white powder-coat finish which offers unparalleled resistance to chipping, scratching, and fading. It is fully marinized which means it will withstand the elements on the water. This unit is 100% waterproof. What makes our technology the best on the market is that our pods are internally wired! This means the terminals are inside the pod and the wires are fed through pre-drilled holes on the pod and clamp. Simply align the wire opening with the hole on your tower and you are done! No exposed wires or terminals! Aluminum cans will last forever!
The sound quality of these are phenomenal! These are the perfect amount of air space to give you the perfect sound quality with the leading marine speakers on the market from brands like Kicker, Rockford Fosgate, etc. Our high efficiency design means more audio output from the same speakers! This means you get louder, cleaner sound with less distortion using our wakeboard enclosures than with other brands.
Features:
- 1 Rockville DMAC80W white aluminum double can wakeboard tower enclosure
- Made of high quality 6061 aircraft grade aluminum
- Beautiful white powder-coat finish
- 100% waterproof and fully marinized against salt and fresh water conditions
- Internally wired for clean install—no exposed wires or terminals
- High efficiency design features the perfect airspace for 7.7” speakers
- Rugged universal mounting clamps made of 6061 aluminum
- Includes precision molded, high impact plastic inserts for tower fitment from 2” diameter to 2.5” diameter
- Mounting depth (in inches): 7.4"
All about your RGHR2:
How To Set Up Your RGHR2:
Included in the box:
- Marine digital media receiver
- Wired remote with 32.8 foot wire
- USB extension cable (40 inches)
- Mounting bracket
- Screws
- ISO wiring
- Owner manual and warranty
Description:
The Rockville RGHR2 is the best gauge hole receiver on the market. We developed this to give you the best sound and the best features.
Crazy loud!
We put in a built in amplifier that is louder than other marine receivers on the market. The RMS power of the built in amp is 28 watt x 4 channels! It is crazy loud and can be heard over the sound of the wind when you are on the water! There is also a built in EQ to customize the sound to your taste.
Included wired remote
Rockville is the only brand on the market that I know of that supplies a wired remote with your radio. The wired remote is a must have for any marine radio. This is great for boats and other powersport applications. We also include an extra long 32.8 foot wire so you will not need any additional extension cables.
Latest listening features
The RGHR2 gives you many listening options. The Bluetooth technology allows you to stream audio from your Bluetooth enabled phone or other music player to the receiver. Our Bluetooth distance is 50 feet! There is also a USB input allowing you to listen to music stored on a thumb drive. You can plug in any audio device to the auxiliary input. There is a built in radio with crystal clear reception as well.
Ability to connect multiple external amps
This receiver makes your system expandable. Two sets of pre-amp outputs allow you to hook up external amps for your speakers and/or subs. This has front and switchable rear/sub pre-amp outputs so you can amplifiy your speakers and a subwoofer amplifier.
Features:
- Rockville RGHR2 Weather Resistant Gauge-Hole Digital Media Receiver w/Bluetooth/USB/AM/FM
- Fits into a standard Gauge-Hole (Tachometer) Opening
- Built-in 72 x 4 Watt Peak high powered amplifier (28 x 4 RMS)
- Built in EQ with preset EQ curves (Pop, Class, Rock, Flat)
- IP66 Waterproof Certification (Tested to withstand the elements)
- USB Input to play back audio files store on a USB thumb drive or any other USB device
- RCA Aux Input
- AM/FM Radio Built In with 18 FM and 12 AM presets + US and European tuning
- Bluetooth built in to stream audio from any Bluetooth enabled device
- USB Input Charges Your Phone
- Two Sets of RCA Outputs (Front and a switchable rear/sub) allow you to connect external amplifiers
- Big easy to use buttons
- Backlit LCD display
- Wired Remote Control Included (normally $50)
- Required cutout: 2.96" (diameter) x 2.75" (depth)
- USB is 500mA and 5V and supports 16GB max
- Dimensions:
- 2.96" cutout mounting diameter
- 4.45" diameter top plate
- 3.9" mounting depth (not including top plate)
- 5.0" depth including the top plate
- Specs of the built in amplifier:
- TDA7851L quadbridge power amplifier
- 4 x 72 watts peak @ 2 ohm
- 4 x 48 watts peak @ 4 ohms
- 4 x 28 watts RMS @ 4 ohms
- Highly efficient even when running at 2 ohms!
- Low distortion even at top volumes
Features:
- Rockville RMWK4 4 AWG Gauge Waterproof Marine/Boat Amplifier Wire Installation Kit
- 20 ’ Translucent, Twisted Pair, High Quality, Tinned-OFC Flexible PVC RCA Cable
- 18’ 4 Gauge High Current, Low Impedance, Clear Flexible Power Cable with 3’ Black Poly Woven Mesh to better resist chemicals in the battery compartment
- 18’ 4 Gauge High Current, Low Impedance, Light Blue, Flexible Ground Cable
- 25’ 16 Gauge 100% Tinned-CCA, White, Non-Transparent Resin PVC, Flat Speaker Cable
- 25’ Blue Remote Wire
- (1) Silver Mini-ANL Fuse Holder – Clear Shell and Clear Blue Bottom Bracket with Blue Waterproof Ring
- (1) 120A Mini-ANL Fuse
- (1) 80A Mini-ANL Fuse
- (2) Ring Terminals
- (2) Spade Terminals
- (5) Speaker Cable Terminals
- (1) Washer
- (10) White Cable Ties
How To Install a Marine Amplifier onto Your Boat:
Video of DBM65:
Includes:
- dBM65 Amplifier
- Bass remote
- PA Microphone
- Birth sheet with Tested Power
- Mounting Screws
- Warranty Card
- Owner’s Manual
Some Popular Configurations:
- 4 full range speakers and 1 or 2 subwoofers
- 8 full range speakers and 1 or 2 subwoofers
- 6 full range speakers (one per channel)
- 12 full range speakers (2 per channel)
- (3) extremely high-powered subwoofers
- Combination of midrange speakers and tweeters
- Combination of subwoofers, full range speakers, and tweeters
There are a ton of other configuration options, because you can bridge any 2 channels of the amp and you can also plug 2 speakers into any single channel of the amp. All channels can be used for full range speakers or for subwoofers since each channel has a crossover. With 110 watts Dyno-Certified per channel @ 2 ohms; each channel has more than enough power for the best speakers on the market.
There is also a really cool feature I wanted to mention quickly. It has 6 channel, 4 channel, and 2 channel selectable input modes. This means if you only have one set of RCA outputs on your receiver, you can run this in 2 channel mode and still have a 6 channel amp to connect many speakers! If you have 3 pairs of preamp outputs you can run the amp in 6 channel input mode. If you have 2 pairs you can select the 4 channel input mode.
Description:
The all new dB marine series of amplifiers gives you the best of both worlds! We took the sound of our best-selling series of dB car amps and we added top of the line marine grade parts so that they will last forever and withstand even the harshest conditions on the water.
We went a little overboard (no pun intended) to make this amp marine ready. We conformal coated the PCB board with a waterproof glue that is painted on to protect the circuitry. We then added waterproof silicone covers over the terminals so that water can never get into the amp. The heat sink, including the bottom plate, is made of aluminum which is rustproof. The end panels, the internal mounting screws and hardware of the amp are made of stainless steel and are rustproof as well. Even after many years of use the amp will be rust free and operate like new!
The DBM65 is a 6-Channel amplifier with 2,600 watts peak output and 650 watts Dyno-Certified power. Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market. The peak rating can be used to compare with brands who use peak ratings such as Boss and Power Acoustik while the Dyno Certified RMS rating can be used to compare with top brands such as Kicker, Rockford, Alpine, etc.
This amp has a very cool fully adjustable 12dB/Octave crossover. What is cool about it is that our crossover supports low pass, high pass, bandpass, and subsonic. This makes our amp ideal for subwoofers (sealed and vented), full range speakers, and midrange speakers. In high pass mode we allow you to filter out frequencies between 15Hz - 4K Hz. In full mode you will not be filtering any frequencies. The really cool part is in low pass mode you can use the high pass and low pass mode. So for example you can set the low pass mode to 50 hz, and then you can set the high pass to 15 Hz. In this case you would be playing frequencies in the range of 15-50 Hz on this channel. This would be an example of using the subsonic filter. Another option you have is for midrange speakers, you can use our low pass filter and set it really high. Lets say to 150 hz. And then you can set the high pass to 3K hz and your midrange speakers will only play that frequency range. Our advanced crossover technology will allow you to really fine tune each speaker to get the sound you desire.
The other cool thing is that this amp has 3 of these crossovers. Every 2 channels has its own set of advanced filters.
As an example; you can use:
Channels 1-2 for 4 full range speakers (in full mode)
Channels 3-4 for 8 midrange speakers (using the bandpass filter)
Channels 5-6 for a subwoofer or 2 (using low pass filter with or without the subsonic)
This amp is capable of supporting almost any setup you can think of.
The dBM65 is protected by a full IC controlled circuitry with mute, delay, and soft start technology to protect your amplifier and speakers from thumping when you turn your vehicle on.
We are so confident that you will be satisfied with this amplifier that we will offer you a 90 day money back guarantee. If this amp does not perform as well as you expected, we will send you a pre-paid shipping label and give you your money back. This means that, if for any reason you want to return the amplifier for a full refund within 90 days, you can! (Amp must be complete along with the box).
Features:
- Rockville DBM65 6-Channel 2600w Peak/660w Dyno-Certified RMS Marine/Boat Amplifier
- Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc)
- 2 Ohm:110 Watts x 6 Channel <1% THD+N
- 4 Ohm: 75 Watts x 6 Channel <1% THD+N
- 4 Ohm Bridged: 220 Watts x 3 Channel
- Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc)
- 2 Ohm: 440 Watts x 6 Channel
- 4 Ohm 300 Watts x 6 Channel
- 4 Ohm Bridged: 880 Watts x 3 Channel
- All channels on the amp have crossovers so they can each be used for subs or full range speakers or midrange or tweeters
- All channels on the amplifier are bridgeable
- Painted Conformal Coating PCB Board (Uses 2577 Waterproof Glue)
- Waterproof silicone covers for end panels
- Rustproof Aluminum heat sink with grey hairline finish
- Stainless steel end panels are rustproof
- All screws and mounting hardware are stainless steel and rustproof
- Bottom panel is aluminum and rustproof
- Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
- Adjustable High Pass Filter: 15Hz -4KHz
- Adjustable Subsonic Filter: 15Hz -40Hz (use both the LPF and HPF knobs)
- Adjustable Low Pass Filter: 40Hz – 4KHz
- Adjustable bandpass filter 15Hz - 4KHz (use both the LPF and HPF knobs)
- Fully Adjustable 12dB Bass Equalizer
- Channels 5&6 are mono only with 24 dB / Octave crossover in Low Pass mode
- Full IC-Controlled Protection Circuitry
- Adjustable input level
- Mute and Delay Soft Start System
- 8 Volt Preamp Circuitry
- 2CH/4CH/6CH Input Mode Switch
- Microphone Input with included PA microphone
- Remote Dashboard Subwoofer Control
- Status Mode LED Indicator
- High-Speed MOSFET Power Supply
- Studio-Grade Bipolar Output Stage Transistors
- Minimum THD at Rated Power: < 0.05%
- S / N Ratio: >90dB
- Frequency Response: 10Hz - 50KHz
- Damping Factor: >80 @ 100Hz
- Optical Coupler Technology
- 30 Amp x 3 ATC Fuse
- Dimensions: (W x H x L) 9? x 2.4? x 19.8?
- Weight: 12.3 Lbs
- UPC:
- 613816441099
