- (1) Rockville DPM10B 10" 400w Powered Active 3-Way Studio Monitor Speaker Full Range
- (1) Rockville PRO-M50 Studio Headphones+Detachable Coil Cable+Case+Extra Ear Pad
- (1) Rockville RCM03 Pro Studio Recording Condenser Microphone Mic+Metal Shock Mount
- (1) Rockville RockShield 1 Studio Microphone Isolation Shield w/Sound Dampening Foam
- (1) Samson MD5 Desktop Mic Stand w/ Weighted Base for Recording, Studio, Podcasting
- (1) Rockville DMS40 40" Microphone Boom Arm Studio Podcast USB Mic Stand+Desk Clamp
How to Set Up your DPM Series Speakers:
Video of DPM10B:
The DPM10B by Rockville is one of the only 10” studio monitors on the market. There is only one other that we have seen. We strongly feel out of the few on the market that ours is the best sounding and best quality.
They have a flat frequency curve making these the perfect studio monitors, but many customers also use these in their home or as stage monitors. These are just about the cleanest sounding speakers you can find. The only reason our price point is not 300 % higher is because you are buying directly from the manufacturer.
To get the most efficiency we use a tri-amp class “AB” amplifier. There are 3 separate amps built into this speaker. One for the lows, one for the mids, and one for the highs. We also added a 3-way crossover that makes sure each component is playing the proper frequencies so that you get the cleanest sound. This is a true 3-way speaker design. We use the best quality components from the amp circuit, to the tweeter, to the woofer, to the enclosure. For highs, we use Ferro fluid enhanced 1.5" neodymium silk dome tweeters. The neo magnet is strong and can handle a lot of heat. This enabled us to beef up the amplifier power without having to worry about melting or blowing the tweeter. The highs on these sound phenomenal! For mids we use a 4” glass Aramid composite midrange. The voice and mids on this speaker are what makes this cleaner than anything else I have ever listened to. The 10” glass Aramid composite woofer gives you some serious bass! What I love about the bass is that you do not get any rumbling effect. It is just clean and musical. The rubber surrounds increase sound quality and eliminate unwanted distortion. The specially wound voice coils produce accurate responses along the entire frequency spectrum. We developed these speakers with the most optimized magnet structure, cone, and cabinet space, with the goal of reproducing the sound to play back exactly the way it was recorded!
Features:
- Rockville DPM10B 10" 3-Way 400W Active/Powered Studio Monitor Speaker in Black (sold individually)
- Peak Power: 400 Watt
- RMS Power: 200 Watt
- True 3-way design With Tri-Amped: 40 Watts for highs, 40 Watts for Mids, and 120 watts for the lows. This speaker has 3 amps built in. It has a separate amp for the lows, mids, and highs. This technology creates the most crisp and clear sound imaginable
- 3-Way Crossover system – Our 3 way crossover built-in is tuned to make sure each speaker plays the proper frequencies. We filter out unwanted sounds from each speaker, and create a flattened frequency curve for the ultimate true sound reproduction
- Midfield monitor with the optimal operating distance of 3 feet to -14 feet
- The front-firing port is built to the perfect spec to enhance the sound and keep a very flat frequency curve
- Curved Front Bezel Design Eliminates Standing Wave Distortion
- Enclosure is made of top quality high-grade MDF wood. The enclosure is 0.5” thick around while the front board of it is a full 1” thick to give you the ultimate best sound quality!
- Tweeter Waveguide design optimizes directivity and phase response providing amazing detail and imaging
- Ferro Fluid Enhanced 1.5" Neodymium Silk Dome Tweeter. Our tweeter produces the softest most realistic highs on the market that will not hurt your ears. They are loud, clear, and musical
- Tweeter has 1” voice coil diameter
- 10” Glass Aramid Composite Woofer cone for excellent transient response and accurate low and mid sound reproduction
- 4” Glass Aramid Composite Midrange for extremely accurate midrange and vocal sound reproduction
- Volume Control: System gain range from -30 dB to +6 dB,
- High Frequency adjusts -2dB, -1dB, 0, +1dB
- Balanced XLR and ¼” TRS line inputs and unbalanced RCA inputs
- The enclosure is built with the perfect amount of air space to maximize sound quality for a studio
- Thermal and Overload / Clip Protection protects the speaker from getting damaged
- Rubber woofer surrounds increase sound quality and eliminate unwanted distortion
- Specially Wound Voice Coils Produce Accurate Responses along Entire Frequency Spectrum
- Round edges and trimmed front wooden front board give you a modern beautiful looking speaker
- Front panel built with black real anodizing aluminum
- Distortion-Free Playback Even at Max Volume Listening! Very Clean Sound!
- Our factory uses the latest Precision Glue Machine (Over 500 meter Tunnel Oven). The glue on the speakers is of the upmost importance. If the glue does not hold up, the speaker is done. We use the latest machinery to manufacture these speakers. The SPL of the speaker goes up when you use better glue and a better machine the secure the glue in place
- Thick “Wadding” protects inside the speaker cabinet – Wadding is a white chemical silk type of material that we put inside the speaker cabinet for multiple reasons. It helps to make the sound come out more clear, and it also protects all the parts inside the speaker. This material is also fire retardant.
- World class top of the line audiophile grade components! We use 3 Amplifier IC’s made by a famous manufacturer called ST. The model is TDA7294. These are known to be best- in-class circuit designs. There are 3 of them since we have 3 amps in the speaker (one for lows, one for mids, one for highs)
- 110/220 Volt compatible
- Every speaker in production undergoes a computer generated sound check test to ensure it upholds to our specifications and standards
- We use a “6Sigma” style Quality Assurance of Each Product (Long story short, each product will work perfectly as advertised for a long long time!)
Specifications:
- Certification: CE and RoHS Compliant
- Amplifier: Class AB, tri-amped
- Max SPL: 113dB at 1w/1m
- THD: 0.10%
- Frequency Response: 31Hz - 20kHz
- Peak output: 400 Watts
- RMS output: 200 Watt
- Input voltage: 120V
- Components: 1.5" neodymium silk dome tweeter, 4” Midrange and 10" woofer with rubber surrounds and glass aramid fiber cone
- Includes power cord, user manual, warranty, and speaker
- Input Impedance (Ohms): 10 K Ohm Balanced
- System Volume: (-30dB to +6dB)
- Product Dimensions in Inches (Single): (W*H*D) 12.8” x 21. 5'' x 14.4''
- Shipping Dimensions in Inches: (W*H*D) 16.3 x 25'' x 17.9''
- Net Weight: 39.7 LBS
- Shipping Weight: 44.5 LBS
All about Your RCM03:
Description:
The Rockville RCM03 condenser microphone performs better than famous branded microphones that cost over $150. This model is similar to our RCM01 however it is made of aluminum, and the frame is slightly larger. We also upgraded this model to a high end metal anti-wind cap! We highly recommend this design. This model is an amazing upgrade to our top selling RCM01 model!
Multi-Purpose
Designed for crystal clear capturing of vocals, acoustic and amplified instruments, as well as room reverb. The frequency pick up pattern makes the RCM03 amazing in studio applications.
The aluminum construction makes the RCM03 tough enough for Live sound applications as well!
Multiple connection options!
This microphone can be used in multiple ways. You can connect this to the phantom power of your mixer or you can connect it directly to your computer sound card. We include both cables! We include a cable to connect it to your mixer as well as a cable to connect the mic to your computer!
Quality built inside and out!
The microphone is made of aluminum. It is very rugged and tough like you would expect from any Rockville product. This microphone has a large diaphragm which is what enables our mic to deliver a wider range of high and low frequencies than our competitors. Our frequency range is tested at 30HZ - 20KHZ! The mic sounds crystal clear sound with no distortion!
The PCB (circuit board) uses surface mounted components which is the same method the expensive brands use. We use only top components that under-go extreme testing by our own audio engineers.
The last thing that I need to mention and call out is that our product is very sturdy. Let me explain. When you are recording, you do not want even the slightest noises coming from your mic. The microphone consists of a casing and there is a cartridge inside the case. You do not want that cartridge moving around. We made sure to adjust our mechanism and ensure the cartridge is firmly in place and not creating any unwanted noises.
Best Value
After testing our Rockville condenser mics against mics that cost 300% more money, we found ours to be as good or better than the ones we tested against.
What's Included:
- RCM03 Condenser Microphone (made of aluminum!)
- 100% Copper 10 foot 3.5mm jack to XLR cable to connect mic to your computer or other device
- 100% Copper 10 foot XLR to XLR cable to connect to any mixer with phantom power
- Metal Shock Mount
- Metal Anti-wind Foam Cap
- Owners Manual
- Warranty Card
Features:
- Rockville RCM03 Pro Studio Recording Condenser Microphone Mic+Metal Shock Mount
- Aluminum high quality construction
- Polar Pattern: Internally Polarized Condenser Cardioid Design
- Large diaphragm for smooth, natural sound and low noise
- Power Requirements: 48V DC Phantom Power
- Uni-directional
- Sensitivity: -27dB±2dB (0dB=1V/Pa at1kHZ)
- Output Impedance: 200O±30% (at 1kHz)
- Standard Operating Voltage: 3V
- Operating Voltage Range: 1.5V-10V
- Current Consumption: Less than 500uA
- Voltage Deduction Characteristic: within 3dB at 2V
- S/N Ratio: More than 24dB
- Frequency Response: 30Hz - 20 KHz
- Fixed Crossover Filter Cutoff Frequency: 40Hz---16 KHz
- Load Impedance: Greater or = to 1000 Ohms
- Equivalent Noise Level: Less than 18dB A (IEC581-5)
- Max. Input SPL: 126dB (THD=1.0% at 1kHZ)
- Electrical Current: Greater than 4.8Ma
- Microphone Body Net Weight: 320 Grams (0.7 Pounds)
- Microphone Max.diameter: 44mm (1.73" inches)
- Microphone Length: 217mm (8.54" inches)
- Microphone Material: Steel grille + Alluminum (handheld part)
- PCB Layout: Surface mount
About Rockville Quality Control Procedures:
The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville products are backed with a hassle free warranty.What's In The Box:
- 3 Panel Mic Isolation Shield
- Hardware to Mount unit to your mic stand
- 5/8” Mic Adapter and 3/8” Mic Adapter
- All metal Tripod Desktop mic attachment
How to Set Up Your RockShield 1:
Video of RockShield 1:
Description:
Rockville’s RockShield 1 compact studio microphone isolation shield is the latest addition to our ever growing line of Pro Audio studio accessories. Featuring 1.5-inch-thick high density acoustic foam, the RockShield1 keeps unwanted outside audio waves and vibrations from affecting your recording. By creating an acoustic boundary around the microphone, vocal audio flow is improved. Your voice is redirected to the microphone, while room reflections are prevented from directly entering the recording area. The end result is you will achieve a crisper and cleaner sound. This shield can be mounted to compatible microphone stands or used in a fixed location, like a counter top or tabletop. Easy installation and studio quality performance will quickly make the RockShield 1 your go-to sound dampening isolation shield.
Features:
- Rockville RockShield 1 Studio Microphone IsolationShield with Sound Dampening Foam
- Number of Panels: 3 Pieces
- Dimensions Each Panel: 8.2'' x 4.5'' inches
- Dimensions Assembled Unit: 11'' x 4.3” x 16.3” inches
- Keeps Excessive Room ambience and Off Axis Sound from interfering with your microphone when recording acoustic and vocal tracks
- Isolates Directional Microphones from Off Axis Coloration
- Limits External Bleed from Unintended Sound Sources
- 1.5" Thick High Density Pyramid Acoustic Foam
- Front and a vented metal back plate for the Best Noise Reflection Reduction
- Can be used in fixed location
- Stand Mountable
- Provides Vocal Booth Style Recordings with Minimal Footprint
- Professional Studio-Grade
- Rugged Finish Makes This Easy to Transport
- Tri-Pod Foot Design for Stability on Flat Surfaces
- 3/8” Die-Cast Metal Threads
- Mic Stand with 5/8” Adapter
- The shield frames are made of high strength die cast aluminum
- Net plates are made of high grade steel
- Net Weight (Without Tripod Stand): 1.1 lbs
- Net Weight (With Tripod Stand): 2.0 lbs
How to Set Up DMS40:
Video of DMS40:
The Rockville DMS40 desktop microphone boom arm is the perfect accessory for any podcast, home studio setup, or broadcasting studio. Its rotating design provides a maximum arm reach of 40" giving you freedom to place your mic anywhere you want!
Our designers used the most sturdy and long lasting clamps and springs, with durable steel construction.
Features:
- Rockville DMS40 40" Studio Desk Clamp Microphone Stand w/Boom Arm
- Articulating microphone boom arm
- Suitable for studios, broadcasting, podcasting, and more
- Arms: 20"+20" arm length for adjustment
- C-shape desk clamp is made of aluminum alloy
- Fits any desk less than 2 inch thick
- ABS plastic mic clip
- You can set the base of the stand on the desk firmly and adjust to your favorite position
- High quality steel frame is sturdy and durable
- Internal springs for silent and effortless positioning
Authorized Samson Dealer!
Description:
Samson's MD5 Desktop Microphone Stand is the ideal tool for any home studio. The MD5 is slim enough to fit on your desk, but also contains a weighted metal base to ensure guaranteed stability and compatibility with any microphone you prefer no matter its size or weight. It's perfect for podcasts, voiceovers, recording music or any other application where high-quality audio is essential. Easy setup and sturdy components make the Samson's MD5 the essential accessory for your desktop studio.
Features:
- Samson MD5 Desktop Mic Stand w/ Weighted Base for Recording, Studio, Podcasting
- Perfect for podcasts, voiceovers, recording vocals, and more!
- 5" desktop microphone stand
- Designed to hold any standard mic for desktop
- Weighted metal base for total stability
- Compatible with Samson's SP01 shockmount
Includes:
- PRO-M50 headphones
- Detachable cable
- Soft suede and leather ear cushions (interchangeable)
- Leather hard travel protective case
- Gold plated ¼" adapter
All About Your PRO-M50:
Description:
Rockville brings you studio quality headphones and at an incredible price with its new PRO-M50 headphones. These are professional grade headphones that are guaranteed to ourperform headphones that cost triple the price! These feature ergonomically designed swiveling cups with interchangeable soft suede or leather finish cushions (included). The ear cups seal tight for excellent sound isolation and minimal bleed. Inside these cups you'll find 40mm Neodymium drivers delivering accurate audio with an extended frequency range for clear and rich bass, and a full frequency range of mids and highs. These are closed back style headphones specifically designed for studio monitoring. These play back the sound with a flat frequency curve so you can hear your music exactly how it was recorded. With the PRO-M50 you can expect to hear every detail of every song with extreme accuracy. These headphones cover full frequency ranges; even extending a bit past the frequencies that the human ear can hear.
The headband is made of soft leather, offering ultimate comfort even after extended wear. The beautifully designed stainless steel headband frame and arms are strong and durable. A detachable 51" coiled 100% Oxygen Free Copper cable with a gold plated 3.5mm plug is included along with a gold plated ¼" adapter to ensure the best possible signal. A hard leather case is included to store and protect your new investment when you are on the go.
Amazing sound quality will make these your go-to headphones whether in the studio or out and about!
Features:
- Rockville PRO-M50 Studio Headphones w/ Detachable Coil Cable, Case+Extra Ear Pad
- Professional High-Definition Studio Headphones
- 40mm Neodymium drivers
- Ergonomically designed swivel ear cups
- Supreme sound isolation
- Accurate sound reproduction
- Minimal bleed
- Sturdy and durable steel headband and arms
- Soft leather headband cover
- Interchangeable leather and soft suede ear cups covers included
- Detachable 51" coil cable made of 100% Oxygen Free Copper (158" fully extended)
- Gold plated 3.5mm connector
- Gold plated ¼" adapter
- Hard leather carrying case
- Stainless steel headband frame and moving arms are durable and long-lasting
Specifications:
- Style: Closed-Back
- Design: Circumaural
- Transducer Type: Dynamic
- Driver: 40MM
- Sensitivity: 97±3dB
- Impedance: 32ohm
- Frequency Response:10Hz - 25KHz
- Max. Power: 600MW
- Rating Power: 260MW
- Net Weight: 290g (with cable)
- UPC:
- 613815839941
