Package Includes:

• (2) Peavey PVX 10 800 Watt 10" Passive 2-Way Pro Audio PA DJ Speaker Monitor PVX10
• (1) Rockville RPA12 5000 Watt Peak / 1400w RMS 2 Channel Power Amplifier Pro/DJ Amp
• (1) Pair Rockville Tripod DJ PA Speaker Stands + Carrying Case Black RVSS2
• (2) Rockville RCTS1610 10' 16 AWG 1/4" TS to Speakon Speaker Cable 100% Copper

---

Authorized Peavey Dealer!

Video of PVX10:

Description of PVX10:

The PVX 10 is a two-way sound reinforcement system based on a heavy-duty 10" woofer and a RX10N titanium diaphragm dynamic compression driver mounted on a 100° x 60° coverage Quadratic Throat Waveguide. Its sleek modern appearance coupled with excellent performance offer an outstanding package.

The lightweight yet rugged injection-molded plastic enclosure with molded-in stand mount cup facilitates portable use for live music or PA sound. The trapezoidal cabinet has two handles for ease of portability, and an extra 45° angled section on the right side to allow use as a floor monitor. Four sets of flying/mounting points, two on the top, two on the bottom, and a pull-back point on the rear, with a total of 13 cabinet inserts, provide for the ultimate in installation flexibility. A black powder coated perforated steel grille provides driver protection and a professional appearance.

The heavy-duty 10” woofer has a 2.4” voice coil diameter, and a 50 oz. magnet for 200 watts continuous worth of thumping bass. The RX 10N compression driver tweeter is coupled to a Quadratic Throat constant directivity waveguide, with smooth, even response, low distortion and good high frequency dispersion. This horn has an asymmetrical vertical polar response, aiming the main energy lobe down 10°, so it is aimed at the audience, instead of over their heads. This helps reduce ceiling reflections for greater clarity and gain before feedback.

The PVX 10 speaker system is rated at 400W program power handling, and the full crossover network includes high voltage film capacitors, high current inductors, and high frequency driver protection for clear punchy sound, and excellent long-term reliability. A 4-pin twist-lock connector and a ¼” phone jack input make hook-up a breeze.

The cabinet of the PVX 10 speaker system has multiple mounting fly points, providing outstanding versatility in permanent install use. A widely spaced pair of M8 inserts molded-in on the top and the bottom for use with eyebolts, and a set of four M8 inserts is available on the top and on the bottom, those in the pattern used for the Peavey VM70 mounting bracket. A pull back point is provided on the rear near the bottom. 

This is a total of 13 mounting inserts in all. All of these inserts have large retaining hardware on the inside of the plastic cabinet, providing a more reliable and safe mode of mounting the cabinet

Features:

• Peavey PVX 10 800 Watt 10" 2-Way Pro Audio PA Speaker
• Program Power Handling: 400 Watts
• Peak Power Handling: 800 Watts
• Two-Way Sound Reinforcement Enclosure
• Crossover Network For Driver Protection And EQ
• High Frequency Driver Protection
• Durable Plastic Injection-Molded Trapezoidal Enclosure
• Asymmetrical Horn Aims The Sound Down 10 Degrees, At The Audience, Not Over Their Heads
• Full-Coverage Heavy-Duty Perforated Steel Grilles, With Powder Coat Finish
• Pole Mount Molded-In
• Top And Bottom Flying Point Inserts
• Patented Quadratic Throat Waveguide Technology, 100° x 60° Coverage
• RX 10N Compression Driver, With 1" Titanium Diaphragm
• 10" Heavy-Duty Woofer With 2.4" Voice Coil & 50 Oz. Magnet
• Extra Angled Section On Right Side Allows Floor Monitor Use
• Product Weight: 25 lb
• Product Dimensions (H x W x D): 20" x 12.7" x 11.06" inches

---

How to Set Up Your RPA12, RPA14, and RPA16:

Video of RPA12:

Power Ratings:

• RMS Power Output:
• Stereo 8 Ohm: 2 x 500W
• Stereo 4 Ohm: 2 x 700W
• Bridged 8 Ohm: 1 x 1400W
• Peak Power Output:
• Stereo 8 Ohm: 2 x 2000W Max
• Stereo 4 Ohm: 2 x 2500W Max
• Bridged 8 Ohm: 1 x 5000W Max

Terminals:

• Input Terminals:
• Combo jack (XLR and ¼”) A & B inputs
• Output Terminals:
• Banana binding post speaker output
• Speakon output
• XLR output to connect another amplifier or powered sub

Features:

• Rockville RPA12 5000 Watt Peak 2 Channel Professional/DJ Rack Mount Amplifier
• LCD displays volume in dB per channel and operating temperature
• 2U rack space
• Built in limiter protects your speakers from distortion and clipping
• Bridged mode allows you to combine both channels power into one channel for use with a subwoofer
• Stereo mode is perfect for (2) speakers or (4) speakers in a left and right configuration
• Parallel mode gives you dual mono output signal which is perfect for monitor use when you want all sounds coming out of each speaker instead of a left/right configuration
• Built in crossover switch (bypass, 80 Hz, 160 Hz) allows amp to be used with full range PA speakers, or Subwoofer(s)
• Channel A & B Clipping Led Indicators
• Channel A & B Separate Level Controls
• Power, signal, clipping, and protection LED indicators on front of amp
• Heavy duty rack mount ears with handles
• Built-in variable high velocity quiet cooling fans
• Maximum headroom for 4-ohm and 8-ohm Speakers
• Level controls for precise setting and matching of sensitivity
• Computer controlled IC protection circuitry against speaker short circuit, thermal over load, DC over load
• User serviceable fuse (15A, 250V)
• Frequency Response (bandwidth @ 2Vrms out, @ -3.0dB) 10 Hz – 30 Khz
• THD + Noise @ 1Khz full power: <0.03%
• Input Impedance: 10K Ohm Balanced
• Input signal voltage: 660mV – 1.5V
• Input sensitivity: 0.7v
• Damping factor: ( 100Hz, 10w, 4 ohms): 40.8
• Damping factor: (1Khz @ 8 ohm): >400:1
• Effective damping factor (100Hz, 10w, 4 Ohms) 1.08
• Output impedance at speaker terminals: 0.09803 Ohms
• Frequency Response vs THD+N (worst case, across normal bandwidth 1W) 0.11%
• Signal to Noise Ratio: > 100dB
• IMD 60Hz & 1kHz, 4:1: <0.04%
• SLEW RATE (input filter limited) : 40v/uS
• Power Requirements: 120V / 50-60Hz
• Weight: 26.5 lbs
• Dimensions: 19.09 x 16.93 x 3.35 inch

 

---

All About Your RVSS2:

How To Set Up Your PA Speaker Stands:

Description:

This heavy-duty universal stand can be used as a Speaker Stand or a Lighting Stand! It's sturdy steel construction and custom carrying case add to the quality and support this stand gives. The sturdy and expandable long tripod legs ensure that your speakers will be stable in any environment.

Includes:

• (2) Tripod Speaker Stands

Features:

• Adjustable Height
• Steel Construction
• Black Color
• Weight Capacity: 132 lbs
• Adjustable Height Range: 47-79 inches
• Base spread: 0-23 inches
• Tube Diameter: 1.38 inches
• Leg Diameter: 1.38 inches

---

The Rockville Difference:

Whenever you see the Rockville shield on a product you know that it has the stamp of approval. While other companies simply import products from China, Rockville manufactures the products in China to lower your cost but do so under American style supervision and quality standards to get you that USA quality that you want!

About Rockville Quality Control Procedures:

The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality.Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville products are backed with a full 1 year warranty, though it is unlikely that you will need to use the warranty.

Great features and great quality make Rockville a great choice.

---

Video of RCTS1610:

Description:

All Rockville pro audio cables are made with 100% copper which boosts the efficiency of the cable. There is nothing better than 100% copper. Most of the cheaper cables on the market do not use 100% copper, instead they make their cables with CCA (Copper Clad Aluminum). CCA cables do not perform on the level that 100% copper cables perform at. CCA will not conduct signals efficiently. A 12 gauge CCA cable will not even perform as well as a 14 gauge 100% pure copper cable, which will in turn, affect the performance and longevity of your equipment. If you find cables on the market that do not mention the copper content, there is a good chance that they are selling you a cheaper cable that is CCA and not 100% copper. Rockville pays an inspection company to oversee the manufacturing of the product to ensure that we provide a 100% Oxygen Free Copper Cable (OFC). Our OFC cables are less prone to oxidation, and will provide maximum signal transfer.

The other important factor of a cable is the shielding. Most of the good brands on the market have about 85% shielding coverage, so we decided to take our shielding a step further. Rockville cables are shielded with a tight copper mesh, covering 90% of the cable! The high percentage of coverage increases the ability to absorb the Electromagnetic Interference (EMI) and Radio Frequency Interference (RFI) that suppresses signal and degrades the performance of equipment. Rockville Cable’s copper shielding provides great flexibility, maintains a durable structural integrity, while decreasing signal interference ensuring enhanced signal clarity with every use.

Features:

• Rockville RCTS1610 16 AWG 1/4" TS to SpeakOn Pro Speaker Cable
• 100% Copper Conductors for Lower Resistance
• Black PVC Jacket for Both Durability and Flexibility
• Intended for High-Current Applications Only, Not Line-Level Signals
• Length: 10 Ft
• Gauge: 16