Package Includes:

• (2) Kicker 10" Car Subwoofers
• (1) Rockville Dual 10” Solo Baric L7/L5/L3 Vented Square Sub Enclosure Box
• (1) Hifonics BXX1200.1D 1200 Watt RMS Mono Amplifier Class D Brutus Car Audio Amp
• (1) Rockville RWK41 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's
• 20 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
• 20 Feet of 14 AWG Blue Speaker Wire
• 4 Spade Terminals

---

Authorized Kicker Dealer!

 

What's In The Box:

• (1) 10" Subwoofer
• (1) Owner's Manual
• (2) Kicker Stickers

Description of Kicker Subs:

The 10-inch L7R Square Sub moves more air and delivers bigger bass than circular subs, so you get more bump out of every watt! The engineers at KICKER invented the original square sub right here in the heart of America. Designed to give you more bass - yet take up no more air space - than a standard round sub. Welcome to the miraculous world of the L7R!

Features:

• KICKER 45L7R104 10" 1000 Watt L7R Car Subwoofer, Solo-Baric 4-Ohm
• RMS Power Handling: 500 Watts
• Peak Power Handling: 1000 Watts
• Frequency Response: 35 Hz - 21 kHz
• Dual Four-Ohm Voice Coil
• Wrap Around Gasketing
• Patented Ribbed Corners
• Injection-Molded SoloKon Woofer
• 360-Degree Back Bracing
• UniPlate Back Plate And Pole Piece
• Bumped Back Plate
• Thick Tinsel Leads
• Large Ceramic Magnet
• Steel Basket With Spoke Design
• Nickel Plated Speaker Terminals
• Sensitivity: 85.9 dB
• Impedance: 4-Ohms
• Mounting Depth: 6.13" inches
• Mounting Diameter: 9.31" inches
• Minimum Sealed Box Volume: 0.66 cubic feet
• Maximum Sealed Box Volume: 1.0 cubic foot
• Minimum Vented Box Volume: 1.25 cubic feet
• Maximum Vented Box Volume: 2.25 cubic feet

Click here for the Owner's Manual

---

Description of BXX1200.1D:

The BXX1200.1D is a 1200 watt mono amplifier featuring Super Class D™ technology with an NGSD digital chip to provide you with an extremely efficient, low temperature, high amplification system that others only dream about. The rock solid Ultra-Fi™ MOSFET outputs are selected for both balance and output power. This keeps power smooth even during demanding peak in the music. All Mono and five channel amplifiers include a bass remote to put the bass control at arm’s length. The amplifiers protection condition is also shown by blue illumination for normal operation and red for a short being present and requires the attention of an installer.

Low Noise Pre-Amplifier Circuitry
Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion

RCA Inputs
Nickel-plated RCA jacks create the most efficient audio connection and resist corrosion

Operation Mode
Mono only

Crossover Type
Variable electronic crossovers allow for complete control of the sound

Electronic Equalizer
Control of amplifier output with on-board electronic crossover to tailor specific frequencies to speakers and subwoofers.

Class / Topology
Super D-Class designs which employ high-speed microprocessors with proprietary d/a conversion algorithms to efficiently control the current consumption. At very high listening levels, Hifonics amplifiers with Super D-Class circuitry result in lower distortion, higher current efficiencies and less heat than conventional D-Class amplifier designs

Output Device Technology
The Ultra-Fi MOSFET is designed for music production vs just electronics output power. It produces very musical high power with high efficiency for cooling and minimal distortion
Heat sink. Classic aluminum Hifonics design to minimize heat build up on the Ultra-Fi output devices

Power Supply
Simpatico coil design. The dual coil pulse width modulated power supply keeps voltage constant through the Ultra-Fi output devices

Output Connections
High temperature impact resistant nickel plated connectors with allen head set screws which allow for secure termination of wire and creates an erosion resistant seal

Connection Type
Molded and angled. Secure connection for all power, ground and speaker connections. Angled for ease of access while creating a clean wire management profile

LED System Protection Circuitry Diagnostics
Monitor overload and speaker short protection with illuminated indicators on the amplifier end panel

Bass Remote Included
Wired bass remote allows adjustments to bass frequencies from the control which can be mounted anywhere in the vehicle.

Phase Adjustment
Phase 0-180°

Features:

• Hifonics Brutus BXX1200.1D 1200 Watt RMS Class D Mono Amplifier
• Power @ 1 Ohm: 1 x 1200 Watts
• Power @ 2 Ohms: 1 x 600 Watts
• Power @ 4 Ohms: 1 x 400 Watts
• Class: Super D Class™
• Variable Voltage: 9V - 0.2V
• Signal to Noise: >95dB
• Frequency Response: 10Hz - 50kHz
• Crossover: Electronic
• Variable Low Pass Crossover 12dB Per Octave: 30Hz - 250Hz
• Bass Boost: 0 - 10dB
• Subsonic Filter: 15Hz - 35Hz
• Phase Shift: 0° - 180°
• Total Channels: 1
• Audio Inputs: RCA
• Audio Outputs: RCA
• Power Terminal 12V/GND: 4 AWG
• Speaker Terminal Wire Gauge: 12 AWG
• Fusing: 80Ax1
• Total Harmonic Distortion (THD): <0.10%

Click here for the Owner's Manual

---

Video of RWK41:

Unboxing Video for RWK41:

Description:

The Rockville RWK41 4 AWG (American Wire Gauge) amp kit has the following differences over other amp kits on the market at this price point.

1. Our RCA cables are 100 % copper. These are top of the line RCA cables

2. Better Resistance: The only thing that really matters with wires is the resistance rating. This is a measurement of conductivity and how much signal is loss per foot of wire. Since Rockville wires are made with around 3 times as much copper as any other wire at this price point, these wires had a much better resistance rating which means they will transfer more power to your amps than the other brands.

3. We do not cheat you on the thickness of the wire. These are standard American wire gauge thickness. This is another reason our conductivity is better than anything else at this price point. Other brands in the market place write 4 gauge, but cheat you on the thickness. We are honest about the thickness.

4. The Rockville amplifier installation kits feature a new soft abrasion proof insulating jacket. This rugged PVC outer jacket allows for 100% improved flexibility over standard power cables making them extremely easy to route through your vehicles interior, and it maintains exceptional resistance to grease and oil. The PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F.

The RCA signal transfer cables included in this kit feature blue and silver twisted pair technology in a clear outer jacket insulation skin. Not only do the blue and silver wires look cool but they also provide superior signal transfer with maximum noise suppression. They are 100% copper to provide absolute lossless perfect signal transfer to your receiver. This technology reduces interference, so your audio signal flows clean and pure at all power levels.

This kit also includes a massive 60 Amp AGU Gold Plated Fuse, so you can be sure it will handle the all the DC power that your amp will need without even the slightest loss of current. The included 7 split loom tube provides protection for your power cable from the typically harsh environment found under the hood of your car.

Audiosavings product experts have tested this amp kit against many leading amp kits on the market and were were impressed not only by the great looks but by the quality of these Rockville installation kits as well. These kits had a lower resistance rating than the other brands we compared and tested them against. What this means is that Rockville manufactures their kits with more copper than other kits at this price point, ultimately providing your amplifiers with better and cleaner DC power, so they work cooler and more efficiently. You will hear the difference a Rockville installation kit will make!

Features:

• 1 – 17’ High Grade Twisted Pair of 100% Copper RCA Cable
• 17’ – 4 Gauge Translucent Blue SuperFlex Power Cables
• 17’ – 18 Gauge Blue Remote Cable
• 17’ – 16 Gauge Clear Speaker Wire
• 3’ – 4 Gauge Clear SuperFlex Ground Wire
• Gold Plated AGU Heat Resistant Fuse Holder
• 60 Amp AGU Gold Plated Fuse
• 7’ Split Tube Loom
• Accessories Included: Wire Ties, Ring Terminals, Butt Connectors, Spades, and Grommets

---

Description of Rockville Enclosure:

The RDVK10 dual 10" vented speaker box is made in the USA with Grade “A” ¾” MDF wood. This enclosure is made with precision cutting machinery by industry experts that have been making these enclosures in the USA for over 20 years. All Rockville enclosures come with a customized enhanced glue that is unmatched by any other manufacturer. That means that the carpet will stay in place and not rip or tear. The ¾” USA MDF is much stronger then any type of import wood.  This will keep your box performing at an optimal level by not flexing and distorting your woofers. Your woofers will thank you!  EVERY Rockville enclosure is not only glued at all joints but stapled as well. If that wasn’t enough we add a layer of silicon to every seam! This makes your Rockville enclosure rock even more!

MADE IN THE USA WITH PRIDE!

Features:

• Rockville RDVK10 Dual Square 10" 1.2 Cu. Ft. Vented Subwoofer Enclosure
• Designed Specifically For The Solo Baric L7/L5/L3 Series Subwoofers and Similar
• Proudly Made In The USA, Using Only The Finest Quality Materials - For The Best Level of Performance From Your Subs!
• 3/4" USA Heavy Duty MDF Construction
• Machine precision cut mounting holes
• Top of the line Glue for extra durable adhesion
• Designed, tested, and engineered to work with most of today’s popular woofers. These enclosures are built with the quality additives needed to maximize the performance of any sound system.
• Tuning frequency: 42Hz

Enclosure Measurements:

• Type of Enclosure: Vented
• Enclosure Sub Size: Dual 10" Square
• Dimensions in Inches: 32" Width x 14.5" Depth x 12" Height
• Top and Bottom Depth: 14.5"
• Mounting Depth: up to 13.75" (enough depth for any sub on the market)
• Gross Volume Per Sub (Measurement for the outer dimensions of the box): 1.6 Cubic Feet
• Net Volume Per Sub (Measurement for the outer dimensions of the box less the thickness of the wood): 1.2 Cubic Feet

---

Complete Dual Subwoofer Enclosure Installation Kit!

Includes:

• 20 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
• 20 Feet of 14 AWG Blue Speaker Wire
• 4 Spade Terminals

This accessory package includes everything you need to install two subwoofers into an enclosure, and wire your enclosure to your amplifier.  This package is a top of the line accessory package which we put together and tested. 

The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure.  The speaker wire is 14 gauge.  This is way better than using 16 gauge.  You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire.  These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly.